Esp positioning
oursland·esp-positioning·kicad/esp-localization.kicad_pcb
About the Esp positioning PCB
Esp positioning is an open source ESP32 PCB design by oursland, published on GitHub. It is a 2-layer board measuring 53.4 × 24.9 mm, with 27 components from 12 distinct parts.
Its main chip is the ESP32-S3-WROOM-2, from the ESP32 family. Other key parts include the ISM330DHCXTR. By type, the board carries 9 resistors, 7 diodes, 5 capacitors, 3 connectors and 2 ICs.
It belongs with the sensors and iot & wireless designs in this gallery.
From the project
There is ample research into the accuracy of Ulra Wideband (UWB)-based ranging and positioning, WiFi Fine Timing Measurements (WiFi FTM)-based ranging and positioning, and an Inertial Measurement Unit (IMU) augmentation of such systems. Most of the work was performed with purpose
There is ample research into the accuracy of Ulra Wideband (UWB)-based ranging and positioning, WiFi Fine Timing Measurements (WiFi FTM)-based ranging and positioning, and an Inertial Measurement Unit (IMU) augmentation of such systems. Most of the work was performed with purpose-designed systems or smartphones, but very little was performed using Espressif SoCs including the ESP32-S3.

Main components on the Esp positioning
Esp positioning bill of materials (BOM)
27 components, 12 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ISM330DHCXTR | LGA-14_2.5X3X0.86_ | IC1 |
| 1 | ESP32-S3-WROOM-2 | ESP32-S3-WROOM-2 | U1 |
| 1 | 2468 | 2468 | J1 |
| 1 | USB_B_Micro | USB_Micro-B_Amphenol_10104110_Horizontal | J2 |
| 1 | TC2030-IDC-NL_ESP | Tag-Connect_TC2030-IDC-NL_2x03_P1.27mm_Vertical | J3 |
| 1 | DWM1000 | DWM1000 | DWM1 |
| 7 | LED_Small | LED_0603_1608Metric | D1, D2, D3, D4, D5, D6, D7 |
| 1 | 1uF | C_0805_2012Metric | C1 |
| 3 | 0.1uF | C_0603_1608Metric | C2, C3, C5 |
| 1 | 22uF | C_0805_2012Metric | C4 |
| 7 | 1k | R_0603_1608Metric | R1, R2, R3, R4, R5, R6, R7 |
| 2 | 10k | R_0603_1608Metric | R8, R9 |
Esp positioning design files
The KiCad project lives in the oursland/esp-positioning repository on GitHub; these links point at the commit this page was built from.
Esp positioning: common questions
What microcontroller does the Esp positioning use?
The Esp positioning is built around the ESP32-S3-WROOM-2, from the ESP32 family.
How big is the Esp positioning PCB?
The Esp positioning measures 53.4 × 24.9 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Esp positioning?
27 components, from 12 distinct parts. The full bill of materials is listed on this page.
Where can I download the Esp positioning design files?
From the oursland/esp-positioning repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Esp positioning design in my own project?
The repository has no license, so all rights stay with oursland. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Esp positioning without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k