40 open source boards using the ESP32-S3-WROOM-2

Real designs built with the ESP32-S3-WROOM-2, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

40 boardsClear filters|Most starred

How designs wire the ESP32-S3-WROOM-2

Read from the KiCad layouts of 26 open source designs, one per repository: what each pin of the ESP32-S3-WROOM-2 connects to, and the resistors, capacitors and other passives placed on it.

  • The EN pin has a pull-up to 3.3V on 20 of 26 designs, most often 10 kΩ (then 5.1 kΩ).
  • The EN pin has a capacitor to GND on 19 of 26 designs, most often 1 µF (then 100 nF).
  • The 3V3 pin is tied to 3.3V on 21 of 26 designs (a signal on 5).
  • The IO46 pin is left unconnected on 15 of 25 designs (a signal on 10).
GNDpin 1, 40, 41Connected to: GND 91%
3V3pin 2Connected to: 3.3V 81% · a signal 19%
ENpin 3Connected to: Signal 92%
  • Pull-up to 3.3V on 77% · 10 kΩ (17), 5.1 kΩ (2), 1 kΩ (1)
  • Capacitor to GND on 73% · 1 µF (12), 100 nF (10), 10 µF (1)
IO46pin 16Connected to: Not connected 60% · a signal 40%
IO0pin 27Connected to: Signal 80% · not connected 20%
  • Pull-up to 3.3V on 36% · 10 kΩ (8), 100 kΩ (1), 4.7 kΩ (1)
NCpin 28, 29, 30Connected to: Not connected 100%

31 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Firestarter by hstarmans, Slider synth by udu3324, Imu rc hand unit by DimitriOnLSD and ES3ink by dronecz.

The ESP32-S3-WROOM-2 in open source designs

The gallery holds 40 open source boards using the ESP32-S3-WROOM-2 from 30 GitHub repositories; a typical one measures about 86.6 × 63.5 mm and carries around 57 components.

74% are two-layer designs, the rest use four layers or more, and 30% carry an open source license.

The most starred is Firestarter by hstarmans.

Microcontrollers on boards using the ESP32-S3-WROOM-2

ESP32-S3-WROOM-2: common questions

Where can I find a ESP32-S3-WROOM-2 reference design?

Each of the 40 boards on this page is a real design using the ESP32-S3-WROOM-2. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the ESP32-S3-WROOM-2 EN pin?

The EN pin has a pull-up to 3.3V on 20 of 26 designs, most often 10 kΩ (then 5.1 kΩ). Counted from the KiCad layouts of 26 open source designs using the ESP32-S3-WROOM-2.

How is the ESP32-S3-WROOM-2 3V3 pin connected?

The 3V3 pin is tied to 3.3V on 21 of 26 designs (a signal on 5). Counted from the KiCad layouts of 26 open source designs using the ESP32-S3-WROOM-2.

How is the ESP32-S3-WROOM-2 IO46 pin connected?

The IO46 pin is left unconnected on 15 of 25 designs (a signal on 10). Counted from the KiCad layouts of 26 open source designs using the ESP32-S3-WROOM-2.

What parts are used alongside the ESP32-S3-WROOM-2?

The AMS1117-3.3, USBLC6-2SC6, TP4056-42-ESOP8, AP2112K-3.3 and LM3940IMPX-3.3_NOPB appear in the most repositories here.

Which microcontrollers do boards using the ESP32-S3-WROOM-2 use?

Most are built on ESP32 (40).

How big is a typical board using the ESP32-S3-WROOM-2?

The median is 86.6 × 63.5 mm, and 74% are two-layer designs.

What is the most popular open source board using the ESP32-S3-WROOM-2?

By GitHub stars, Firestarter by hstarmans, with 9 stars.

Can I simulate one of these boards using the ESP32-S3-WROOM-2 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part