Beuth printed sensor hw
pdt590·beuth-printed-sensor-hw
About the Beuth printed sensor hw PCB
Beuth printed sensor hw is an open source ESP32 PCB design by pdt590, published on GitHub. It is a 2-layer board measuring 46.6 × 52.1 mm, with 32 components from 24 distinct parts.
Its main chip is the ESP32-WROOM-32, from the ESP32 family. Other key parts include the MCP73831 and AP2112K-3.3. By type, the board carries 9 resistors, 6 capacitors, 5 diodes, 3 ICs and 1 transistor.
It belongs with the sensors designs in this gallery.
From the project
Readout device hardware for PrintED
Readout device hardware for PrintED project
Front | Edge :---------------------------------:|:--------------------------------------: |
- beuth-printed-sensor-fw - beuth-printed-app - beuth-printed-cloud

Main components on the Beuth printed sensor hw
Beuth printed sensor hw bill of materials (BOM)
32 components, 24 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MCP73831 | SOT-23-5_HandSoldering | U1 |
| 1 | AP2112K-3.3 | SOT-23-5_HandSoldering | U2 |
| 1 | ESP32-WROOM-32 | ESP32-WROOM-32 | U3 |
| 1 | 2.5A/30V | SOT-23_Handsoldering | Q1 |
| 1 | LiPo | JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | BATTERY1 |
| 1 | BME680 | PinHeader_1x07_P2.54mm_Vertical | BME1 |
| 1 | Switch | SW_SPST_B3U-1000P-B | EN1 |
| 1 | Conn_01x07 | PinHeader_1x06_P2.54mm_Vertical | FLASH1 |
| 1 | LIS3DH | PinHeader_1x08_P2.54mm_Vertical | LIS1 |
| 1 | MOISTURE | PinHeader_1x03_P2.54mm_Vertical | MOISTURE1 |
| 1 | USB_B_Micro | USB_Micro-B_Wuerth_629105150521 | USB1 |
| 1 | Conn_01x07 | PinHeader_1x02_P2.54mm_Vertical | VIN1 |
| 2 | Red | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1, D2 |
| 1 | 1A/23V/620mV | D_SOD-323_HandSoldering | D3 |
| 1 | Green | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D4 |
| 1 | Blue | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D5 |
| 2 | 4.7uF/6.3V | C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C1, C2 |
| 2 | 1.0uF/6.3V | C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C3, C4 |
| 1 | 0.1uF/50V | C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C5 |
| 1 | 10uF/10V | C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C6 |
Show 4 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | 10K | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R1, R7, R9 |
| 4 | 1K | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R2, R3, R4, R8 |
| 1 | 100K | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R5 |
| 1 | 1.0K | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R6 |
Beuth printed sensor hw design files
The KiCad project lives in the pdt590/beuth-printed-sensor-hw repository on GitHub; these links point at the commit this page was built from.
- Layoutclip.kicad_pcb
Beuth printed sensor hw: common questions
What microcontroller does the Beuth printed sensor hw use?
The Beuth printed sensor hw is built around the ESP32-WROOM-32, from the ESP32 family.
How big is the Beuth printed sensor hw PCB?
The Beuth printed sensor hw measures 46.6 × 52.1 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Beuth printed sensor hw?
32 components, from 24 distinct parts. The full bill of materials is listed on this page.
Where can I download the Beuth printed sensor hw design files?
From the pdt590/beuth-printed-sensor-hw repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Beuth printed sensor hw design in my own project?
The repository has no license, so all rights stay with pdt590. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Beuth printed sensor hw without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k