Esp32-c3-sensor board
petekaik·esp32-c3-sensor-board·hardware/esp32-c3-sensor-board-rev2.kicad_pcb
About the Esp32-c3-sensor board
Esp32-c3-sensor board is an open source ESP32 PCB design by petekaik, published on GitHub. It is a 2-layer board measuring 46 × 89 mm, with 10 components from 9 distinct parts.
Its main chip is the ESP32-C3-SuperMini, from the ESP32 family. Other key parts include the HLK-LD2410C. By type, the board carries 5 connectors, 3 jumpers and 2 ICs.
It belongs with the sensors, iot & wireless and dev boards & breakouts designs in this gallery, and the repository also holds 1 earlier revision of it.
From the project
Wall-mountable carrier for an ESP32-C3 Super Mini that exposes the module's GPIO, power and comms for plug-in sensor and peripheral modules. Hardware only — the ESPHome configuration lives in a separate project (doorbell.yml is the authoritative pin/feature map).
Wall-mountable carrier for an ESP32-C3 Super Mini that exposes the module's GPIO, power and comms for plug-in sensor and peripheral modules. Hardware only — the ESPHome configuration lives in a separate project (doorbell.yml is the authoritative pin/feature map).
Current board: rev2, 46 × 89 mm, 2-layer, USB-C on the top short edge.
Female sockets are fitted on the carrier; the modules carry male pins. Relay and button remain screw/plug connections.

Main components on the Esp32-c3-sensor board
Esp32-c3-sensor board bill of materials (BOM)
10 components, 9 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3-SuperMini | ESP32-C3-SuperMini_Socket | U1 |
| 1 | HLK-LD2410C | ld2410c | U2 |
| 1 | BME280_Module | PinSocket_1x06_P2.54mm_Vertical | J1 |
| 1 | BH1750_Module | PinSocket_1x05_P2.54mm_Vertical | J2 |
| 1 | Relay | PinSocket_1x03_P2.54mm_Horizontal | J3 |
| 1 | Button | TerminalBlock_MaiXu_MX126-5.0-02P_1x02_P5.00mm | J4 |
| 1 | BREAKOUT | breakout_1x14 | J5 |
| 2 | Jumper | PinHeader_1x03_P2.54mm_Vertical | JP1, JP2 |
| 1 | Jumper | PinHeader_1x02_P2.54mm_Vertical | JP3 |
Esp32-c3-sensor board design files
The KiCad project lives in the petekaik/esp32-c3-sensor-board repository on GitHub; these links point at the commit this page was built from.
Esp32-c3-sensor board: common questions
What microcontroller does the Esp32-c3-sensor board use?
The Esp32-c3-sensor board is built around the ESP32-C3-SuperMini, from the ESP32 family.
How big is the Esp32-c3-sensor board?
The Esp32-c3-sensor board measures 46 × 89 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Esp32-c3-sensor board?
10 components, from 9 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Esp32-c3-sensor board design files?
From the petekaik/esp32-c3-sensor-board repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Esp32-c3-sensor board design in my own project?
The repository has no license, so all rights stay with petekaik. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Esp32-c3-sensor board without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Earlier revisions in the repo: esp32-c3-sensor-board
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k