HardLabs

360-Lizard-RE

Pheeeeenom·360-Lizard-RE·hw/360 Lizard/lizard_clone_jlcpcb/lizard.kicad_pcb

360-Lizard-RE PCB layout, top view — open source PIC board by Pheeeeenom

About the 360-Lizard-RE PCB

360-Lizard-RE is an open source PIC PCB design by Pheeeeenom, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 72.8 × 43.1 mm, with 93 components from 43 distinct parts.

Its main chip is the PIC18F87J11T-I_PT, from the PIC family. Other key parts include the FT232RL, AP1121B, 74LVC1G04, MIC2290 and W25Q32JVSS. By type, the board carries 39 capacitors, 25 resistors, 7 ICs, 6 connectors, 3 battery holders and 3 LEDs.

From the project

This is a completely reverse engineered 360 Lizard. The ultimate xbox 360 flashing tool.

Mostly for preservations sake, but it really annoyed me having to deal with Windows 10/11 and driver issues, old LTU pcb's getting stuck on "writing .", JungleFlasher using very suspicious remote execution dll's (I'll be going into the software side later in the docs), the clutter of having to having cables all over the place/pc needing to be open to get access to a SATA plug. List goes on.

360-Lizard-RE, from the project README
From the project README

Main components on the 360-Lizard-RE

FT232RLPIC18F87J11T-I_PTAP1121B74LVC1G04MIC2290W25Q32JVSS

360-Lizard-RE bill of materials (BOM)

93 components, 43 distinct parts.

QtyPartRefs
1
FT232RL
U1
1
PIC18F87J11T-I_PT
U2
1
~
U3
1
AP1121B
U5
1
74LVC1G04
U6
1
MIC2290
U7
1
W25Q32JVSS
U8
1
AO3401A
Q1
1
10MHz
Y1
1
20MHz
Y2
1
SATA
CN1
1
Conn_01x12_Pin
CN2
2
Conn_01x04_Pin
CN3, J3
1
Micro_SD_Card
J1
1
USB_B_Mini
J2
3
SW_Push
BT0, BT1, BT2
1
SK-3296S-01-L1
SW0
1
MSS22C02KG10-B
SW1
1
BLUE
LED1
1
GREEN
LED2
Show 23 more
QtyPartRefs
1
RED
LED3
1
1N4148W
D2
1
MBR0520
D3
1
330nH
FB1
1
330nH
FB2
1
10uH
L2
19
100nF
C1, C2, C3, C4, C8, C9, C10, C11 +11
3
10uF
C5, C21, C22
4
24pF
C6, C7, C17, C18
1
1uF
C16
2
10uF
C20, C32
1
10nF
C23
4
47nF
C25, C26, C27, C28
4
5uF
C29, C30, C31, C34
1
2.7uF
C33
14
10k
R1, R3, R4, R5, R6, R8, R9, R10 +6
2
31.6k
R2, R23
1
12k
R7
3
110
R11, R12, R14
1
1k
R13
2
270
R19, R21
1
1M
R20
1
910k
R34

360-Lizard-RE design files

The KiCad project lives in the Pheeeeenom/360-Lizard-RE repository on GitHub; these links point at the commit this page was built from.

360-Lizard-RE: common questions

What microcontroller does the 360-Lizard-RE use?

The 360-Lizard-RE is built around the PIC18F87J11T-I_PT, from the PIC family.

How big is the 360-Lizard-RE PCB?

The 360-Lizard-RE measures 72.8 × 43.1 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the 360-Lizard-RE?

93 components, from 43 distinct parts. The full bill of materials is listed on this page.

Where can I download the 360-Lizard-RE design files?

From the Pheeeeenom/360-Lizard-RE repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the 360-Lizard-RE design in my own project?

Yes, under the terms of its GPL-3.0 license, which Pheeeeenom chose for the repository.

Can I test firmware for the 360-Lizard-RE without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug PIC firmware against it before you order a PCB.

Similar boards