Garage opener
physiii·garage-opener·hardware/garage-opener.kicad_pcb
About the Garage opener PCB
Garage opener is an open source ESP32 PCB design by physiii, published on GitHub. It is a 2-layer board measuring 83.5 × 48.5 mm, with 46 components from 25 distinct parts.
Its main chip is the ESP-WROOM-02, from the ESP32 family. Other key parts include the FT230XS and SPX3819. By type, the board carries 16 resistors, 8 diodes, 7 capacitors, 3 ICs, 3 transistors and 3 connectors.
Main components on the Garage opener
Garage opener bill of materials (BOM)
46 components, 25 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP-WROOM-02 | ESP-WROOM-02 | U1 |
| 1 | FT230XS | SSOP-16_3.9x4.9mm_Pitch0.635mm | U2 |
| 1 | SPX3819 | SOT-23-5 | U11 |
| 1 | MMBT3904LT1G | SOT-23 | Q1 |
| 1 | 2N7002L | SOT-23 | Q2 |
| 1 | BSS84LT1G | SOT-23 | Q3 |
| 1 | 10118194-0001LF USB_OTG | USB_Micro-B | P1 |
| 1 | ESPM02200 1935161 | bornier2 | P2 |
| 1 | CONN_01X04 | Pin_Header_Angled_1x04 | P3 |
| 1 | CONN_01X06 | Pin_Header_Straight_1x06 | JP1 |
| 2 | CONN_01X10 | Pin_Header_Straight_1x10 | JP2, JP3 |
| 1 | 893-833H-1C-S-5VDC 833H-1C-S-5VDC | 883H | RL1 |
| 1 | SW_PUSH | SW_SPST_KMR2 | SW2 |
| 5 | LED | LED_0805 | D1, D4, D7, D8, D9 |
| 1 | MBR120VLSFT1G ZENER | SOD-123 | D2 |
| 2 | SS14 | SMA_Standard | D5, D6 |
| 1 | BK0603HS330-T | R_0603 | FB1 |
| 2 | VJ0805G106KXQTW1BC 1uf | C_0603 | C1, C2 |
| 1 | VJ0805G106KXQTW1BC 0.1uf | C_0603 | C3 |
| 1 | KEM_C1002_X7R_SMD-357932 4.7uf | C_0603 | C4 |
Show 5 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | VJ0603A470JXACW1BC 47pF | C_0603 | C5, C6 |
| 1 | VJ0603A470JXACW1BC 100nF | C_0603 | C7 |
| 12 | ERJ-1GE0R00C 1K | R_0603 | R1, R2, R4, R6, R7, R8, R9, R12 +4 |
| 2 | ERJ-1GE0R00C 10K | R_0603 | R3, R5 |
| 2 | ERJ-1GE0R00C 27K | R_0603 | R10, R11 |
Garage opener design files
The KiCad project lives in the physiii/garage-opener repository on GitHub; these links point at the commit this page was built from.
Garage opener: common questions
What microcontroller does the Garage opener use?
The Garage opener is built around the ESP-WROOM-02, from the ESP32 family.
How big is the Garage opener PCB?
The Garage opener measures 83.5 × 48.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Garage opener?
46 components, from 25 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Garage opener design files?
From the physiii/garage-opener repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Garage opener design in my own project?
The repository has no license, so all rights stay with physiii. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Garage opener without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k