Window sensor
physiii·window-sensor·hardware/window-sensor.kicad_pcb
About the Window sensor PCB
Window sensor is an open source ESP32 PCB design by physiii, published on GitHub. It is a 2-layer board measuring 83.5 × 48.5 mm, with 51 components from 26 distinct parts.
Its main chip is the ESP-WROOM-02, from the ESP32 family. Other key parts include the OPA344NA/3K, CMC-5044PF-A, FT230XS, TSL2581FN and SI7055-A20-IM. By type, the board carries 21 resistors, 9 capacitors, 7 ICs, 5 diodes, 3 jumpers and 2 transistors.
It belongs with the iot & wireless and sensors designs in this gallery.
From the project
wifi window sensor
Main components on the Window sensor
Window sensor bill of materials (BOM)
51 components, 26 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP-WROOM-02 | ESP-WROOM-02 | U1 |
| 1 | OPA344NA/3K OP275 | SOIC-8_3.9x4.9mm_Pitch1.27mm | U2 |
| 1 | CMC-5044PF-A | Electret | U3 |
| 1 | FT230XS | SSOP-16_3.9x4.9mm_Pitch0.635mm | U4 |
| 1 | TSL2581FN | DFN-6-1EP_2x2mm_Pitch0.65mm | U5 |
| 1 | SI7055-A20-IM Si7055-A20-IM | DFN-6-1EP_3x3mm_Pitch0.95mm | U6 |
| 1 | ERJ-3GEYJ103V SPX3819 | SOT-23-5 | U11 |
| 1 | 2N7002L | SOT-23 | Q1 |
| 1 | BSS84LT1G | SOT-23 | Q2 |
| 1 | 10118194-0001LF USB_OTG | USB_Micro-B | P1 |
| 1 | CONN_01X06 | Pin_Header_Straight_1x06 | JP1 |
| 2 | CONN_01X10 | Pin_Header_Straight_1x10 | JP4, JP5 |
| 1 | ZENER | SOD-123 | MBR120-1 |
| 1 | SW_PUSH | SW_SPST_KMR2 | SW2 |
| 5 | LED | LED_0805 | D1, D2, D3, D4, D5 |
| 1 | BLM18PG330SN1D | R_0603 | FB1 |
| 2 | VJ0805G475KXYTW1BC 4.7uF | C_0805 | C1, C8 |
| 1 | GRM0335C1H120GA01D 12pF | R_0603 | C2 |
| 1 | VJ0805G106KXQTW1BC 10uf | C_0805 | C3 |
| 1 | C0603X5R1C472K030BA 4.7 uF | C_0603 | C4 |
Show 6 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | VJ0603A470JXACW1BC 47pf | C_0603 | C5, C6, C7, C9 |
| 10 | ERJ-3EKF1001V 1K | R_0603 | R1, R6, R8, R13, R14, R15, R16, R17 +2 |
| 2 | ERJ-3GEYJ270V 27R | R_0603 | R2, R4 |
| 5 | ERJ-3GEYJ103V 10K | R_0603 | R3, R5, R9, R10, R12 |
| 1 | ERJ-3GEYJ105V 1M | R_0603 | R7 |
| 3 | ERJ-3GEYJ222V 2.2K | R_0603 | R11, R18, R19 |
Window sensor design files
The KiCad project lives in the physiii/window-sensor repository on GitHub; these links point at the commit this page was built from.
Window sensor: common questions
What microcontroller does the Window sensor use?
The Window sensor is built around the ESP-WROOM-02, from the ESP32 family.
How big is the Window sensor PCB?
The Window sensor measures 83.5 × 48.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Window sensor?
51 components, from 26 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Window sensor design files?
From the physiii/window-sensor repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Window sensor design in my own project?
The repository has no license, so all rights stay with physiii. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Window sensor without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k