Watch v1
PyMite6941·watch_v1·assets/watch_v1/watch_v1.kicad_sch
About the Watch v1 PCB
Watch v1 is an open source ESP32 PCB design by PyMite6941, published on GitHub. It is a board, with 38 components from 19 distinct parts.
Its main chip is the ESP32-C3 SuperMini, from the ESP32 family. Other key parts include the 5643A-1 4-digit 7-segment, TP4056 Li-Po Charger and MCP1700-33 3.3V LDO. By type, the board carries 20 resistors, 4 ICs, 4 transistors, 2 switches, 2 diodes and 2 capacitors.
It belongs with the power & battery, wearables and displays & leds designs in this gallery.
From the project
ESP32-C3 SuperMini watch: 4-digit 7-segment display, touch buttons, LDR auto-brightness, RGB LED, haptics, Li-Po battery, USB-C charging, clear 3D-printed enclosure
This directory contains the OpenSCAD source files for the watch enclosure.
Main components on the Watch v1
Watch v1 bill of materials (BOM)
38 components, 19 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3 SuperMini | Header_2x13_2.54mm | U1 |
| 1 | 5643A-1 4-digit 7-segment | Header_2x07_2.54mm | U2 |
| 1 | TP4056 Li-Po Charger | DIP-8 | U3 |
| 1 | MCP1700-33 3.3V LDO | TO-92 | U4 |
| 1 | Coin Vibration Motor | Connector_2pin | M1 |
| 4 | 2N2222 NPN | TO-92 | Q1, Q2, Q3, Q4 |
| 1 | USB-C Receptacle | USB_C_Receptacle | J1 |
| 1 | 3.7V 150mAh Li-Po | JST_PH_2pin | BT1 |
| 2 | Tactile Button | Switch_Tactile | SW1, SW2 |
| 1 | Common Cathode RGB LED | LED_RGB_TH | LED1 |
| 1 | 1N5819 Schottky (BAT→LDO) | DO-41 | D1 |
| 1 | 1N5819 Schottky (USB→LDO) | DO-41 | D2 |
| 2 | 1uF | CP_Radial_D5.0mm_P2.50mm | C1, C2 |
| 11 | 220 | R_Axial_DIN0207_L3.6mm_D1.6mm_P2.54mm_Horizontal | R1, R2, R3, R4, R5, R6, R7, R8 +3 |
| 4 | 4.7k | R_Axial_DIN0207_L3.6mm_D1.6mm_P2.54mm_Horizontal | R9, R10, R11, R12 |
| 1 | 10k | R_Axial_DIN0207_L3.6mm_D1.6mm_P2.54mm_Horizontal | R13 |
| 1 | 12k | R_Axial_DIN0207_L3.6mm_D1.6mm_P2.54mm_Horizontal | R14 |
| 1 | 1k | R_Axial_DIN0207_L3.6mm_D1.6mm_P2.54mm_Horizontal | R18 |
| 2 | 100k | R_Axial_DIN0207_L3.6mm_D1.6mm_P2.54mm_Horizontal | R19, R20 |
Watch v1 design files
The KiCad project lives in the PyMite6941/watch_v1 repository on GitHub; these links point at the commit this page was built from.
- Schematicassets/watch_v1/watch_v1.kicad_sch
Watch v1: common questions
What microcontroller does the Watch v1 use?
The Watch v1 is built around the ESP32-C3 SuperMini, from the ESP32 family.
How many components are on the Watch v1?
38 components, from 19 distinct parts. The full bill of materials is listed on this page.
Where can I download the Watch v1 design files?
From the PyMite6941/watch_v1 repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the Watch v1 design in my own project?
The repository has no license, so all rights stay with PyMite6941. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Watch v1 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k