Quadruped robot
RayaneGuebre·Quadruped-Robot·PCB/Quadruped robot.kicad_pcb
About the Quadruped robot PCB
Quadruped robot is an open source ESP32 PCB design by RayaneGuebre, published on GitHub. It is a 2-layer board measuring 100 × 130 mm, with 5 components from 5 distinct parts.
Its main chip is the ESP32-S3-DEVKITC-1-N8R2, from the ESP32 family. By type, the board carries 4 connectors and 1 IC.
It belongs with the robotics & motion designs in this gallery.
From the project
My first robot
the motherboard connects each pin of the esp32 to a screw terminal for future upgrades and changes
Main components on the Quadruped robot
Quadruped robot bill of materials (BOM)
5 components, 5 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-DEVKITC-1-N8R2 | XCVR_ESP32-S3-DEVKITC-1-N8R2 | U1 |
| 1 | Screw_Terminal_01x04 | Altech_AK100_1x04_P5.00mm | J1 |
| 1 | Screw_Terminal_01x03 | Altech_AK100_1x03_P5.00mm | J2 |
| 1 | Screw_Terminal_01x20 | Altech_AK100_1x20_P5.00mm | J3 |
| 1 | Screw_Terminal_01x17 | Altech_AK100_1x17_P5.00mm | J4 |
Quadruped robot design files
The KiCad project lives in the RayaneGuebre/Quadruped-Robot repository on GitHub; these links point at the commit this page was built from.
Quadruped robot: common questions
What microcontroller does the Quadruped robot use?
The Quadruped robot is built around the ESP32-S3-DEVKITC-1-N8R2, from the ESP32 family.
How big is the Quadruped robot PCB?
The Quadruped robot measures 100 × 130 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Quadruped robot?
5 components, from 5 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Quadruped robot design files?
From the RayaneGuebre/Quadruped-Robot repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Quadruped robot design in my own project?
The repository has no license, so all rights stay with RayaneGuebre. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Quadruped robot without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Quadruped-Robot
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k