PCB-Business-Card
rganlath3·PCB-Business-Card·PCB_Design/Business_Card/Business_Card.kicad_pcb
About the PCB-Business-Card
PCB-Business-Card is an open source Nordic nRF PCB design by rganlath3, published on GitHub under the CERN-OHL-S-2.0 license. It is a 2-layer board measuring 85.6 × 54 mm, with 14 components from 7 distinct parts.
Its main chip is the XIAO nRF52840, from the Nordic nRF family. By type, the board carries 6 resistors, 5 switches, 1 IC, 1 connector and 1 battery holder.
It belongs with the displays & leds and power & battery designs in this gallery.
From the project
A business card with embedded IPS display
This PCB is used to interface a XIAO nRF5240 Sense with the following components: - SMD Pushbuttons - IPS Display - Power Source (Lipo Battery)
I did some research on artistic designs and found people using soldermask as a visual aesthetic. When the board is finished with ENIG, it produces a protected and nice gold finish. For the board thickness I went with 0.8mm. (Typical board is 1.6mm). For future revisions, I may make the board even thinner. The end goal is not use a breakout board and to simply have the nRF5240 or another board like the ESP32-S3 bare chip used along with battery…

Main components on the PCB-Business-Card
PCB-Business-Card bill of materials (BOM)
14 components, 7 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO nRF52840 | XIAO-nRF52840-SMD_Revised | U1 |
| 1 | 1-14in IPS ST7789V Display | 1-14in_IPS_ST7789V_Display | J1 |
| 1 | Lipo Connector | PinHeader_2x01_P2.00mm_Vertical_SMD | BT1 |
| 1 | Main Power | PinHeader_2x01_P2.00mm_Vertical_SMD | SW1 |
| 4 | SW_Push | SW_SPST_TL3342 | SW2, SW3, SW4, SW5 |
| 5 | 10kohm | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R1, R3, R4, R5, R6 |
| 1 | 22kohm | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R2 |
PCB-Business-Card design files
The KiCad project lives in the rganlath3/PCB-Business-Card repository on GitHub; these links point at the commit this page was built from.
PCB-Business-Card: common questions
What microcontroller does the PCB-Business-Card use?
The PCB-Business-Card is built around the XIAO nRF52840, from the Nordic nRF family.
How big is the PCB-Business-Card?
The PCB-Business-Card measures 85.6 × 54 mm, has 2 copper layers and is 0.8 mm thick.
How many components are on the PCB-Business-Card?
14 components, from 7 distinct parts. The full bill of materials is listed on this page.
Where can I download the PCB-Business-Card design files?
From the rganlath3/PCB-Business-Card repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the PCB-Business-Card design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which rganlath3 chose for the repository.
Can I test firmware for the PCB-Business-Card without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Nordic nRF firmware against it before you order a PCB.
Similar boards
Nordic nRF
Keyboard
byrantech
262.5 × 109.6 mm206 parts2LMIT4.3kNordic nRF
TOTEM
GEIGEIGEIST
258.8 × 94.4 mm85 parts2LCERN-OHL-P-2.02.0kNordic nRF
Pixl.js
solosky
40 × 23 mm45 parts4LGPL-2.01.4kNordic nRF
Board hl15-latest
dennisss
61 × 37 mm14 parts2LApache-2.0381Nordic nRF
Management
dennisss
101 × 31.5 mm50 parts2LApache-2.0381Nordic nRF
Board
dennisss
363 × 128 mm420 parts4LApache-2.0381