Electronic-Speed-Controller

rhysyim·Electronic-Speed-Controller·PCB/Triple Half Bridge Driver v4b3/PCB/PCB.kicad_pcb

Electronic-Speed-Controller PCB layout, top view — open source RP2040/RP2350 board by rhysyim

About the Electronic-Speed-Controller PCB

Electronic-Speed-Controller is an open source RP2040/RP2350 PCB design by rhysyim, published on GitHub. It is a 2-layer board measuring 311 × 221.5 mm, with 367 components from 29 distinct parts.

Its main chip is the RaspberryPi_Pico, from the RP2040/RP2350 family. Other key parts include the IRS2101, LM7812_TO220, LM7805_TO220 and LM393. By type, the board carries 118 resistors, 82 connectors, 53 capacitors, 30 test points, 21 diodes and 19 transistors.

From the project

Electronic Speed Controller of Brushless DC Motor

A hardware implementation using comparators to compare BEMF of motor in /PCB/Triple Half Bridge Driver v4b2. The original implementatoin with current sensing amplifier in /PCB/Triple Half Bridge Driver v4a (footprints not in place yet).

Main components on the Electronic-Speed-Controller

Electronic-Speed-Controller bill of materials (BOM)

367 components, 29 distinct parts.

QtyPartRefs
6
IRS2101
U1, U2, U3, U10, U11, U12
2
RaspberryPi_Pico
U4, U16
1
LM7812_TO220
U5
1
LM7805_TO220
U6
3
LM393
U7, U8, U9
4
~
U17, U18, U19, U20
6
Q_PNP_BEC
Q1, Q2, Q3, Q13, Q16, Q19
12
IRF740
Q4, Q5, Q6, Q7, Q8, Q9, Q14, Q15 +4
1
IRF9540N
Q10
3
Screw_Terminal_01x06
J1, J7, J8
6
Screw_Terminal_01x03
J2, J14, J21, J24, J25, J85
6
Screw_Terminal_01x03
J3, J4, J5, J13, J15, J16
46
Screw_Terminal_01x02
J6, J9, J10, J11, J12, J17, J18, J19 +38
4
Screw_Terminal_01x01
J23, J28, J44, J70
1
Screw_Terminal_01x02
J26
16
Screw_Terminal_01x02
J27, J29, J30, J31, J32, J33, J34, J35 +8
15
R_Potentiometer
RV1, RV2, RV3, RV4, RV5, RV6, RV7, RV8 +7
2
SW_Push
SW1, SW2
30
TestPoint
TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8 +22
8
VAL**
mouse-bite-2.54mm-slot, mouse-bite-2.54mm-slot2, mouse-bite-2.54mm-slot3, mouse-bite-2.54mm-slot4, mouse-bite-2.54mm-slot5, mouse-bite-2.54mm-slot7, mouse-bite-2.54mm-slot8, mouse-bite-2.54mm-slot9
Show 9 more
QtyPartRefs
6
D
D1, D2, D3, D7, D10, D13
13
D_Schottky
D4, D5, D6, D8, D9, D11, D12, D14 +5
2
LED
D26, D27
2
FerriteBead
FB1, FB2
6
4.7uF 35V
C1, C2, C3, C11, C16, C21
47
C
C4, C5, C6, C7, C8, C9, C10, C12 +39
111
R
R1, R2, R3, R4, R5, R6, R7, R8 +103
6
10k
R13, R14, R15, R16, R17, R18
1
0
R77

Electronic-Speed-Controller design files

The KiCad project lives in the rhysyim/Electronic-Speed-Controller repository on GitHub; these links point at the commit this page was built from.

Electronic-Speed-Controller: common questions

What microcontroller does the Electronic-Speed-Controller use?

The Electronic-Speed-Controller is built around the RaspberryPi_Pico, from the RP2040/RP2350 family.

How big is the Electronic-Speed-Controller PCB?

The Electronic-Speed-Controller measures 311 × 221.5 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Electronic-Speed-Controller?

367 components, from 29 distinct parts. The full bill of materials is listed on this page.

Where can I download the Electronic-Speed-Controller design files?

From the rhysyim/Electronic-Speed-Controller repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Electronic-Speed-Controller design in my own project?

The repository has no license, so all rights stay with rhysyim. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Electronic-Speed-Controller without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

Similar boards