Open mabel
robotmabel·open_mabel·electrical/Motherboard/Motherboard.kicad_pcb
About the Open mabel PCB
Open mabel is an open source NXP PCB design by robotmabel, published on GitHub under the Apache-2.0 license. It is a 2-layer board measuring 95.5 × 83 mm, with 73 components from 36 distinct parts.
Its main chip is the DEV-16771, from the NXP family. Other key parts include the TCAN330, LM1117MP-3.3, BNO085, ACS724LLCTR-50AB and MP1584EN. By type, the board carries 24 resistors, 23 capacitors, 10 ICs, 10 connectors, 4 diodes and 1 crystal.
It belongs with the robotics & motion designs in this gallery.
From the project
MABEL: open-source mobile bimanual robot — hardware, firmware, control, ROS 2, simulation, learning
The only custom PCB: a Teensy 4.1 carrier that runs the swerve base. Everything else is off-the-shelf (see ../hardware/bom/).
1. Zip Motherboard/fab/ and upload it to any 2-layer PCB service (stack-up in fab/Motherboard-job.gbrjob). 2. Source parts from the schematic (exports/Motherboardschematic.pdf) and the BOM. 3. Flash the firmware: ../firmware/swervedrive/.

Main components on the Open mabel
Open mabel bill of materials (BOM)
73 components, 36 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | TCAN330 | TSOT-23-8 | U1, U5, U6 |
| 1 | LM1117MP-3.3 | SOT-223-3_TabPin2 | U2 |
| 1 | DEV-16771 | Teensy41 | U3 |
| 1 | BNO085 | IC_BNO085 | U4 |
| 3 | ACS724LLCTR-50AB | SOIC-8_3.9x4.9mm_P1.27mm | U7, U8, U9 |
| 1 | MP1584EN | SOIC127P600X170-9N | U10 |
| 1 | 32.768kHz | Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | SPI2 | JST_SH_SM08B-SRSS-TB_1x08-1MP_P1.00mm_Horizontal | J1 |
| 1 | CAN1 | TerminalBlock_MaiXu_MX126-5.0-03P_1x03_P5.00mm | J2 |
| 1 | CAN2 | TerminalBlock_MaiXu_MX126-5.0-03P_1x03_P5.00mm | J3 |
| 1 | CAN3 | TerminalBlock_MaiXu_MX126-5.0-03P_1x03_P5.00mm | J4 |
| 1 | power-output2 | AMASS_XT30PW-M_1x02_P2.50mm_Horizontal | J5 |
| 1 | power-output3 | AMASS_XT30PW-M_1x02_P2.50mm_Horizontal | J6 |
| 1 | power-output1 | AMASS_XT30PW-M_1x02_P2.50mm_Horizontal | J7 |
| 1 | power-input | AMASS_XT60-F_1x02_P7.20mm_Vertical | J8 |
| 1 | I2C | JST_SH_SM06B-SRSS-TB_1x06-1MP_P1.00mm_Horizontal | J9 |
| 1 | J1B1211CCD | J1B1211CCD | P1 |
| 2 | SS34 | D_SMA | D1, D2 |
| 2 | LED | LED_0805_2012Metric | D3, D4 |
| 1 | 15uH | L_APV_APH0630 | L1 |
Show 16 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 15 | 0.1uF | C_0805_2012Metric | C1, C2, C3, C4, C5, C6, C7, C10 +7 |
| 2 | 18pF | C_0805_2012Metric | C8, C9 |
| 1 | 10uF/50V | C_1210_3225Metric | C18 |
| 1 | 220pF | C_0805_2012Metric | C21 |
| 1 | DNP (NS) | C_0805_2012Metric | C22 |
| 3 | 22uF/16V | C_1206_3216Metric | C24, C25, C26 |
| 3 | 120R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R3 |
| 10 | 10k | R_0805_2012Metric | R4, R5, R6, R7, R8, R9, R10, R12 +2 |
| 3 | 15k | R_0805_2012Metric | R11, R13, R15 |
| 1 | 52.3k | R_0805_2012Metric | R17 |
| 1 | 68.1k | R_0805_2012Metric | R18 |
| 1 | 200k | R_0805_2012Metric | R19 |
| 1 | 100k | R_0805_2012Metric | R20 |
| 1 | 47k | R_0805_2012Metric | R21 |
| 1 | 5.6k | R_0805_2012Metric | R22 |
| 2 | 330R | R_0805_2012Metric | R23, R24 |
Open mabel design files
The KiCad project lives in the robotmabel/open_mabel repository on GitHub; these links point at the commit this page was built from.
Open mabel: common questions
What microcontroller does the Open mabel use?
The Open mabel is built around the DEV-16771, from the NXP family.
How big is the Open mabel PCB?
The Open mabel measures 95.5 × 83 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Open mabel?
73 components, from 36 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Open mabel design files?
From the robotmabel/open_mabel repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Open mabel design in my own project?
Yes, under the terms of its Apache-2.0 license, which robotmabel chose for the repository.
Can I test firmware for the Open mabel without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug NXP firmware against it before you order a PCB.
Similar boards
NXP
32Bit shift register
MaltWhiskey
100 × 54 mm56 parts4LNo license763NXP
Mega-Cube-Board
MaltWhiskey
200 × 54 mm100 parts4LNo license763NXP
MCL6809
MicroCoreLabs
32.3 × 61 mm7 parts4LNo license532NXP
MCL68
MicroCoreLabs
31.6 × 84.1 mm13 parts4LNo license532NXP
MCL65+
MicroCoreLabs
72.6 × 64.1 mm6 parts2LNo license532NXP
MCLZ8
MicroCoreLabs
37.1 × 61.5 mm6 parts4LNo license532