12 open source boards using the TCAN330

Real designs built with the TCAN330, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

12 boardsClear filters|Most starred

How designs wire the TCAN330

Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the TCAN330 connects to, and the resistors, capacitors and other passives placed on it.

  • The CANL pin has a series resistor on 9 of 11 designs, most often 120 Ω (then 60.4 Ω).
  • The CANH pin has a series resistor on 9 of 11 designs, most often 120 Ω (then 60.4 Ω).
  • The VCC pin has a decoupling capacitor on 7 of 11 designs, most often 100 nF (then 2.2 µF).
GNDpin 2Connected to: GND 91%
VCCpin 3Connected to: 3.3V 82% · a signal 18%
  • Decoupling capacitor on 64% · 100 nF (8), 2.2 µF (4)
CANLpin 6Connected to: A connector 100%
  • Series resistor on 82% · 120 Ω (9), 60.4 Ω (1)
CANHpin 7Connected to: A connector 100%
  • Series resistor on 82% · 120 Ω (9), 60.4 Ω (1)

4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Open mabel by robotmabel, FlexiBMS hardware by SimosMCmuffin, G431 M2006 ESC by EMakerDragon and Oresat live card by oresat.

The TCAN330 in open source designs

The gallery holds 12 open source boards using the TCAN330 from 11 GitHub repositories; a typical one measures about 84.8 × 80 mm and carries around 80 components.

55% use four copper layers or more, and 25% carry an open source license.

The most starred is Open mabel by robotmabel.

Microcontrollers on boards using the TCAN330

What boards using the TCAN330 are built for

TCAN330: common questions

Where can I find a TCAN330 reference design?

Each of the 12 boards on this page is a real design using the TCAN330. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the TCAN330 CANL pin?

The CANL pin has a series resistor on 9 of 11 designs, most often 120 Ω (then 60.4 Ω). Counted from the KiCad layouts of 11 open source designs using the TCAN330.

What resistor goes on the TCAN330 CANH pin?

The CANH pin has a series resistor on 9 of 11 designs, most often 120 Ω (then 60.4 Ω). Counted from the KiCad layouts of 11 open source designs using the TCAN330.

What decoupling capacitors do designs use on the TCAN330 VCC pin?

The VCC pin has a decoupling capacitor on 7 of 11 designs, most often 100 nF (then 2.2 µF). Counted from the KiCad layouts of 11 open source designs using the TCAN330.

What parts are used alongside the TCAN330?

The AP2210N-3.3, ISL28022, LTC3873, LTC6803-3 and MAX17502F appear in the most repositories here.

Which microcontrollers do boards using the TCAN330 use?

Most are built on STM32 (9), NXP (1) and RP2040/RP2350 (1).

How big is a typical board using the TCAN330?

The median is 84.8 × 80 mm, and 45% are two-layer designs.

What is the most popular open source board using the TCAN330?

By GitHub stars, Open mabel by robotmabel, with 41 stars.

Can I simulate one of these boards using the TCAN330 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part