StreamPixel
RockingRidz·StreamPixel·electronics/source/StreamPixel.kicad_pcb
About the StreamPixel PCB
StreamPixel is an open source ESP32 PCB design by RockingRidz, published on GitHub under the MIT license. It is a 2-layer board measuring 100 × 65 mm, with 22 components from 14 distinct parts.
Its main chip is the ESP32-WROOM-32E, from the ESP32 family. Other key parts include the 74HCT245 and AP2112K-3.3. By type, the board carries 8 capacitors, 4 ICs, 4 connectors, 3 resistors, 2 switches and 1 fuse.
From the project
StreamPixel is Ridith Shetty's three-panel RGB display project. The proposed build combines three P10 panels, an ESP32 controller, 5V logic buffers and a microphone for sound-reactive display effects. The nominal display is 96 × 16 pixels across a 960 × 160 mm panel array.
StreamPixel is Ridith Shetty's three-panel RGB display project. The proposed build combines three P10 panels, an ESP32 controller, 5V logic buffers and a microphone for sound-reactive display effects. The nominal display is 96 × 16 pixels across a 960 × 160 mm panel array.
Current status: design and fit review. No assembled or working hardware demo is claimed. The CAD now includes a ventilated rear cover, six removable panel retainers, controller tray, supply cradle, wall spacers, splice plates, cable exit and engraved project/creator names. Real panel and supply measurements, printing…

Main components on the StreamPixel
StreamPixel bill of materials (BOM)
22 components, 14 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-WROOM-32E | ESP32-WROOM-32E | U1 |
| 2 | 74HCT245 | DIP-20_W7.62mm | U2, U3 |
| 1 | AP2112K-3.3 | SOT-23-5 | U4 |
| 1 | Conn_02x08_Odd_Even | IDC-Header_2x08_P2.54mm_Vertical | J1 |
| 1 | Conn_01x06_Pin | PinHeader_1x06_P2.54mm_Vertical | J2 |
| 1 | Conn_01x02_Pin | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J3 |
| 1 | PIN8 SELECT GND-P8-E | PinHeader_1x03_P2.54mm_Vertical | J4 |
| 1 | PTC 1A hold 6V min | Fuse_1206_3216Metric | F1 |
| 2 | SW_Push | SW_PUSH_6mm | SW1, SW2 |
| 3 | 10uF 16V X7R | C_0805_2012Metric | C1, C2, C3 |
| 3 | 100nF 16V X7R | C_0805_2012Metric | C4, C5, C6 |
| 1 | 1uF 16V X7R | C_0805_2012Metric | C7 |
| 1 | 470uF 10V | CP_Radial_D8.0mm_P3.50mm | C8 |
| 3 | 10k | R_0805_2012Metric | R1, R2, R3 |
StreamPixel design files
The KiCad project lives in the RockingRidz/StreamPixel repository on GitHub; these links point at the commit this page was built from.
StreamPixel: common questions
What microcontroller does the StreamPixel use?
The StreamPixel is built around the ESP32-WROOM-32E, from the ESP32 family.
How big is the StreamPixel PCB?
The StreamPixel measures 100 × 65 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the StreamPixel?
22 components, from 14 distinct parts. The full bill of materials is listed on this page.
Where can I download the StreamPixel design files?
From the RockingRidz/StreamPixel repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the StreamPixel design in my own project?
Yes, under the terms of its MIT license, which RockingRidz chose for the repository.
Can I test firmware for the StreamPixel without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k