MiniOscilloscope

RoseDaggerDev·MiniOscilloscope·KiCAD/MiniOSCI/MiniOSCI.kicad_pcb

MiniOscilloscope PCB layout, top view — open source PIC board by RoseDaggerDev

About the MiniOscilloscope PCB

MiniOscilloscope is an open source PIC PCB design by RoseDaggerDev, published on GitHub under the MIT license. It is a 4-layer board measuring 25 × 25 mm, with 79 components from 50 distinct parts.

Its main chip is the VQFN-64-1EP_9x9mm_P0.5mm_EP7.15x7.15mm, from the PIC family. Other key parts include the MIC4428, CPC1017N, TLV75533PDBV, TLV9062xDSG and 4052. By type, the board carries 34 capacitors, 27 resistors, 6 ICs, 5 diodes, 3 connectors and 1 transistor.

From the project

Through-Hole Version: Its been fully tested and works like a charm. Its got a BOM of 87 components and fits on a 50x50mm 2-layer board, manufactured by PCBWay. It took around 3.5 hours to solder after prepping all the components. I underestimated the IC socket size, so things got

Through-Hole Version: Its been fully tested and works like a charm. Its got a BOM of 87 components and fits on a 50x50mm 2-layer board, manufactured by PCBWay. It took around 3.5 hours to solder after prepping all the components. I underestimated the IC socket size, so things got a bit tight with some parts had to be nudged sideways. I also used the wrong footprint size for the ceramic caps, so they’re a little squished, but everything still worked out in the end!

Main components on the MiniOscilloscope

MIC4428CPC1017NTLV75533PDBVTLV9062xDSG4052

MiniOscilloscope bill of materials (BOM)

79 components, 50 distinct parts.

QtyPartRefs
1
MIC4428
U1
1
CPC1017N
U2
1
~
U3
1
TLV75533PDBV
U4
1
TLV9062xDSG
U5
1
4052
U7
1
DMC3071LVT
Q1
1
Crystal_GND24
Y1
1
Conn_01x05_Pin
J1
1
USB_C_Receptacle_USB2.0_16P
J2
1
Conn_01x02_Pin
J3
1
5k
RV1
1
BAT54SDW
D1
1
LED
D2
1
BZX84Cxx
D3
2
BAT54S
D4, D5
1
L
L1
2
100u
C1, C17
1
1n
C2
10
100n
C3, C4, C5, C11, C12, C13, C19, C27 +2
Show 30 more
QtyPartRefs
8
1u
C6, C7, C10, C15, C18, C23, C25, C33
2
20p
C8, C9
1
1u
C14
1
10u
C16
1
10u
C20
1
100p
C21
1
680p
C22
1
470p
C24
1
2p2
C26
1
47p
C29
1
15p
C30
1
6p8
C31
1
10p
C32
5
1k
R1, R16, R17, R18, R24
2
10k
R2, R13
2
100
R3, R4
2
5.1k
R5, R6
1
100
R7
2
150
R8, R9
1
5k1
R10
3
20k
R11, R14, R21
1
2k7
R12
1
1k5
R15
1
7k5
R19
1
11k
R20
1
75k
R22
1
15k
R23
1
100k
R25
1
2.2
R26
1
R_Pack08
RN1

MiniOscilloscope design files

The KiCad project lives in the RoseDaggerDev/MiniOscilloscope repository on GitHub; these links point at the commit this page was built from.

MiniOscilloscope: common questions

What microcontroller does the MiniOscilloscope use?

The MiniOscilloscope is built around the VQFN-64-1EP_9x9mm_P0.5mm_EP7.15x7.15mm, from the PIC family.

How big is the MiniOscilloscope PCB?

The MiniOscilloscope measures 25 × 25 mm, has 4 copper layers and is 0.6 mm thick.

How many components are on the MiniOscilloscope?

79 components, from 50 distinct parts. The full bill of materials is listed on this page.

Where can I download the MiniOscilloscope design files?

From the RoseDaggerDev/MiniOscilloscope repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the MiniOscilloscope design in my own project?

Yes, under the terms of its MIT license, which RoseDaggerDev chose for the repository.

Can I test firmware for the MiniOscilloscope without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug PIC firmware against it before you order a PCB.

Similar boards