9 open source boards using the CPC1017N
Real designs built with the CPC1017N, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Voctoknopf1
benjaminwand
161.3 × 88.5 mm44 parts2LNo license6FPGA
ICE40hxk4 dev board
smartbench
67 × 157 mm379 parts4LNo license2AFE
Blaze-Pascal
100 × 100 mm198 parts4LGPL-3.02PIC
MiniOscilloscope
RoseDaggerDev
25 × 25 mm79 parts4LMIT1STM32
PROJ500 - Power Distribution Board
AislingBee
99.1 × 108.6 mm297 parts2LNo license0Mesa-7i96s-P1-Port-BOB
Szymon423
52.5 × 98 mm104 parts2LCC-BY-4.00RP2040/RP2350
Pikvm atxboard switch
L0czek
99.7 × 99.7 mm62 parts2LNo license0Analog board
smartbench
36.6 × 44.5 mm48 parts2LNo license2STM32
Digital Board Rev 1
jer-lil
101.6 × 101.6 mm85 parts4LNo license0
How designs wire the CPC1017N
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the CPC1017N connects to, and the resistors, capacitors and other passives placed on it.
- Pin 2 is tied to GND on 6 of 8 designs.
- Pin 1 has a series resistor on 4 of 8 designs, most often 1 kΩ (then 150 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 88% |
|
| Pin 2 | Connected to: GND 75% | — |
| Pin 4 | Connected to: A connector 38% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Voctoknopf1 by benjaminwand, AFE by Blaze-Pascal, Analog board by smartbench and MiniOscilloscope by RoseDaggerDev.
The CPC1017N in open source designs
The gallery holds 9 open source boards using the CPC1017N from 8 GitHub repositories; a typical one measures about 99.1 × 99.7 mm and carries around 85 components.
56% are two-layer designs, the rest use four layers or more, and 33% carry an open source license.
The most starred is Voctoknopf1 by benjaminwand.
Microcontrollers on boards using the CPC1017N
What boards using the CPC1017N are built for
CPC1017N: common questions
Where can I find a CPC1017N reference design?
Each of the 9 boards on this page is a real design using the CPC1017N. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the CPC1017N pin 2 connected?
Pin 2 is tied to GND on 6 of 8 designs. Counted from the KiCad layouts of 8 open source designs using the CPC1017N.
What resistor goes on the CPC1017N pin 1?
Pin 1 has a series resistor on 4 of 8 designs, most often 1 kΩ (then 150 Ω). Counted from the KiCad layouts of 8 open source designs using the CPC1017N.
Which microcontrollers do boards using the CPC1017N use?
Most are built on STM32 (2), FPGA (1), PIC (1) and RP2040/RP2350 (1).
How big is a typical board using the CPC1017N?
The median is 99.1 × 99.7 mm, and 56% are two-layer designs.
What is the most popular open source board using the CPC1017N?
By GitHub stars, Voctoknopf1 by benjaminwand, with 6 stars.
Can I simulate one of these boards using the CPC1017N before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.