Wrenchboard
Rowninator·wrenchboard·boards/uno_r3/Arduino UNO.kicad_pcb
About the Wrenchboard PCB
Wrenchboard is an open source AVR/Arduino PCB design by Rowninator, published on GitHub. It is a 2-layer board measuring 68.6 × 53.3 mm, with 51 components from 33 distinct parts.
Its main chip is the ATMEGA16U2-MU, from the AVR/Arduino family. Other key parts include the NCP1117-5.0_SOT223, LP2985-3.3, ATMEGA328P-PU and LMV358IDGKR. By type, the board carries 13 capacitors, 9 connectors, 8 resistors, 7 diodes, 5 ICs and 2 crystals.
From the project
If you are taking the parts from an OEM UNO like I did, I recommend using low-melt solder to aid in the desoldering of through-hole components. The surface mount components come off easily enough with hot air, but when removing the reset switch or electrolytic capacitors, try to
If you are taking the parts from an OEM UNO like I did, I recommend using low-melt solder to aid in the desoldering of through-hole components. The surface mount components come off easily enough with hot air, but when removing the reset switch or electrolytic capacitors, try to heat them from the bottom of the board to avoid applying too much direct heat.
Below are the screenshots of this board from KiCad's 3D board viewer.
Main components on the Wrenchboard
Wrenchboard bill of materials (BOM)
51 components, 33 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | NCP1117-5.0_SOT223 | SOT-223-3_TabPin2 | U1 |
| 1 | LP2985-3.3 | SOT-23-5 | U2 |
| 1 | ATMEGA16U2-MU | VQFN-32-1EP_5x5mm_P0.5mm_EP3.1x3.1mm | U3 |
| 1 | ATMEGA328P-PU | DIP-28_W7.62mm_Socket | U4 |
| 1 | LMV358IDGKR | MSOP-8_3x3mm_P0.65mm | U5 |
| 1 | FDN340P | SC-59 | Q1 |
| 1 | CSTNE16M0V530000R0 | Resonator_SMD_Murata_CSTxExxV-3Pin_3.0x1.1mm | Y1 |
| 1 | LFXTAL003240BULK | Crystal_HC49-4H_Vertical | Y2 |
| 2 | M20-9980345 | PinHeader_2x03_P2.54mm_Vertical | J1, J3 |
| 1 | M20-9980245 | CONN_M20-9980245_HRW | J2 |
| 1 | PPTC101LFBN-RC | PinSocket_1x10_P2.54mm_Vertical | J4 |
| 2 | PPTC081LFBN-RC | PinSocket_1x08_P2.54mm_Vertical | J5, J7 |
| 1 | PPTC061LFBN-RC | PinSocket_1x06_P2.54mm_Vertical | J6 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J8 |
| 1 | PJ-102AH | BarrelJack_Kycon_KLDX-0202-xC_Horizontal | J9 |
| 1 | MF-MSMF050-2 | Fuse_1812_4532Metric_Pad1.30x3.40mm_HandSolder | F2 |
| 1 | TS06-667-30-BK-100-G-SMT-TR | SW_TS06-667-30-BK-100-G-SMT-TR | S1 |
| 2 | 5pF@1MHz | R_0603_1608Metric | Z1, Z2 |
| 1 | CGRB307-G | D_SMB | D1 |
| 2 | CD1206-S01575 | D_1206_3216Metric | D2, D3 |
Show 13 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | YELLOW | LED_0805_2012Metric | D4, D5, D6 |
| 1 | GREEN | LED_0805_2012Metric | D7 |
| 1 | 1kΩ@100MHz | L_0805_2012Metric | FB1 |
| 1 | 10uH | L_0805_2012Metric | FB2 |
| 2 | 47u | CAP_EEHZA1E470P | C1, C2 |
| 7 | 100n | C_0603_1608Metric | C3, C4, C6, C7, C8, C9, C12 |
| 2 | 1u | C_0603_1608Metric | C5, C10 |
| 2 | 22p | C_0603_1608Metric | C11, C13 |
| 2 | 1M | R_0603_1608Metric | R1, R2 |
| 2 | 5k1 | R_0603_1608Metric | R3, R4 |
| 1 | 10k | R_Array_Convex_4x0603 | RN1 |
| 2 | 1k | R_Array_Convex_4x0603 | RN2, RN4 |
| 1 | 22R | R_Array_Convex_4x0603 | RN3 |
Wrenchboard design files
The KiCad project lives in the Rowninator/wrenchboard repository on GitHub; these links point at the commit this page was built from.
Wrenchboard: common questions
What microcontroller does the Wrenchboard use?
The Wrenchboard is built around the ATMEGA16U2-MU, from the AVR/Arduino family.
How big is the Wrenchboard PCB?
The Wrenchboard measures 68.6 × 53.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Wrenchboard?
51 components, from 33 distinct parts. The full bill of materials is listed on this page.
Where can I download the Wrenchboard design files?
From the Rowninator/wrenchboard repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Wrenchboard design in my own project?
The repository has no license, so all rights stay with Rowninator. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Wrenchboard without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k