MCB-100-A

Rudolfs-Pakalns·Line-Follower·Line_Follower_PCBs/MCB/MCB-100-A/MCB-100-A.kicad_pcb

MCB-100-A PCB layout, top view — open source AVR/Arduino board by Rudolfs-Pakalns

About the MCB-100-A PCB

MCB-100-A is an open source AVR/Arduino PCB design by Rudolfs-Pakalns, published on GitHub. It is a 2-layer board measuring 116.3 × 74.1 mm, with 42 components from 29 distinct parts.

Its main chip is the ATmega32U4-A, from the AVR/Arduino family. Other key parts include the DRV8833PWP. By type, the board carries 12 capacitors, 12 resistors, 8 connectors, 4 diodes, 3 switches and 2 ICs.

It belongs with the robotics & motion designs in this gallery.

From the project

My personal line follower robot project

Main components on the MCB-100-A

MCB-100-A bill of materials (BOM)

42 components, 29 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
DRV8833PWP
U1
1
ATmega32U4-A
U2
1
Crystal_GND24
Y1
1
MOT A
J1
1
MOT B
J2
1
USB_C_Receptacle_USB2.0_16P
J3
1
BT
J4
1
Signals
J6
1
Power
J7
1
Conn_01x03_Pin
J9
1
SPI
J14
1
USER
SW1
1
Sl_En
SW2
1
RESET
SW3
1
RX_LED
D3
1
TX_LED
D4
1
FAULT
D5
1
D_Schottky
D12
6
100n
C1, C2, C3, C6, C15, C16
2
20p
C4, C5
Show 9 more
QtyPartRefs
1
1u
C7
1
10u
C12
1
2u2
C13
1
10n
C14
3
10k
R1, R4, R15
2
22
R2, R3
3
1k
R10, R11, R12
2
0.2
R13, R14
2
5k1
R31, R32

MCB-100-A design files

The KiCad project lives in the Rudolfs-Pakalns/Line-Follower repository on GitHub; these links point at the commit this page was built from.

MCB-100-A: common questions

What microcontroller does the MCB-100-A use?

The MCB-100-A is built around the ATmega32U4-A, from the AVR/Arduino family.

How big is the MCB-100-A PCB?

The MCB-100-A measures 116.3 × 74.1 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the MCB-100-A?

42 components, from 29 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the MCB-100-A design files?

From the Rudolfs-Pakalns/Line-Follower repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the MCB-100-A design in my own project?

The repository has no license, so all rights stay with Rudolfs-Pakalns. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the MCB-100-A without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in Line-Follower

Similar boards