53 open source boards using the DRV8833PWP
Real designs built with the DRV8833PWP, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Langpie
langpie
100 × 100 mm60 parts2LNo license48STM32
OpenHand v3
AleksaHeler
100 × 50 mm181 parts4LMIT11STM32
NeuroBot
viktorvano
70 × 90 mm70 parts2LMIT9Rover Motor Driver
ElectronicCats
40 × 70 mm26 parts2LGPL-3.09STM32
PiZumo Robot
wallComputer
66 × 83.1 mm70 parts4LGPL-2.03ESP32
Yunyu esp32
yunyu-x
40 × 40 mm18 parts4LApache-2.03STM32
AratMicro
vorlaxen-labs
80 × 87.6 mm102 parts4LMIT1ESP32
OmniDrive
TLNKhanh
45 × 59.5 mm66 parts2LMIT1PCBRev2
MilesMayhew
213.4 × 128.3 mm63 parts2LNo license1STM32
OpenHand v3
iamprince3
100 × 50 mm181 parts4LNo license0STM32
LineFollower
InderveerS
110 × 68 mm103 parts2LNo license0Astra-Companion-NOISEEE
atireksd11
122 × 140 mm103 parts4LNo license0STM32
Garbage Collector
Rouaa-spec
78 × 68 mm98 parts4LMIT0ESP32
Robotpcbv1
NIKOLAI-GOGOL444
52.1 × 52.1 mm85 parts4LApache-2.00Betr kicad resources
TheUnknownAlias
56.6 × 39 mm85 parts4LCustom license0ESP32
Swarm Robot Hardware
Khoi281248
62.8 × 62.8 mm83 parts2LMIT0ESP32
The48ErrCar
iustinG-afk
97.8 × 66.2 mm74 parts2LMIT0STM32
Drone controller project
MohamadAminGhanoum
69 × 56.5 mm70 parts4LNo license0EEE3088 Power-Subsystem 2025
miruokami
119.2 × 55 mm70 parts2LNo license0EEE3088F Project 2025
Rasekoai
77.3 × 55.5 mm68 parts2LNo license0ESP32
RC-Car
GIANT-Zera
80 × 64 mm66 parts2LMIT0STM32
Micromouse
Andy46
70 × 90 mm61 parts4LNo license0EEE3088F MM Power Project
KLPJOA002
77.3 × 58.5 mm59 parts2LNo license0RP2040/RP2350
Plant-Monitor
C-yue28
42.8 × 66.3 mm59 parts6LNo license0MM-Power-Module
Cago-M
82 × 60 mm58 parts2LNo license0EEE3088F-Design-Project
maarijbhai
80.6 × 61 mm54 parts2LNo license0RP2040/RP2350
Half monty-2
neilpstevenson
47.7 × 45.5 mm50 parts2LMIT0Acebott Shield Version A
Athenkosi-Khonzani
57 × 53 mm43 parts2LNo license0AVR/Arduino
MCB-100-A
Rudolfs-Pakalns
116.3 × 74.1 mm42 parts2LNo license0ESP32
Thermometer
RolandThsive
71.9 × 68.9 mm31 parts2LCC-BY-NC-4.00ESP32
Terrascout grounded
partofcosmos-site
100 × 80 mm29 parts2LCERN-OHL-S-2.00Maze Solver Shield VSDSquadron
brijeshahirwar100
57.9 × 29.5 mm13 parts4LNo license0Thingy
nimitvijayvargee
50.8 × 66 mm11 parts2LNo license0- schematic only · 59 parts
Project
Innocentmkhonta
59 partsNo license0 - schematic only · 58 parts
EEE3088Proj
SanjanNaidoo
58 partsNo license0 - schematic only · 8 parts
MotorDriver DRV8833
triakshasingh
8 partsNo license0
How designs wire the DRV8833PWP
Read from the KiCad layouts of 43 open source designs, one per repository: what each pin of the DRV8833PWP connects to, and the resistors, capacitors and other passives placed on it.
- The VINT pin has a capacitor to GND on 36 of 43 designs, most often 2.2 µF (then 10 µF).
- The VM pin has a decoupling capacitor on 28 of 43 designs, most often 10 µF (then 100 nF).
- The VCP pin has a capacitor to the supply on 22 of 43 designs, most often 10 nF (then 100 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| AISENpin 3 | Connected to: GND 53% · a signal 42% |
|
| BISENpin 6 | Connected to: GND 56% · a signal 42% |
|
| VCPpin 11 | Connected to: Signal 88% |
|
| VMpin 12 | Connected to: 5V 63% · a signal 33% |
|
| GNDpin 13, 17 | Connected to: GND 94% | — |
| VINTpin 14 | Connected to: Signal 84% |
|
10 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Langpie by langpie, OpenHand v3 by AleksaHeler, Rover Motor Driver by ElectronicCats and NeuroBot by viktorvano.
The DRV8833PWP in open source designs
The gallery holds 53 open source boards using the DRV8833PWP from 48 GitHub repositories; a typical one measures about 73.6 × 60.5 mm and carries around 58 components.
71% are two-layer designs, the rest use four layers or more, and 36% carry an open source license.
The most starred is Langpie by langpie.
Parts used alongside the DRV8833PWP
Microcontrollers on boards using the DRV8833PWP
What boards using the DRV8833PWP are built for
DRV8833PWP: common questions
Where can I find a DRV8833PWP reference design?
Each of the 53 boards on this page is a real design using the DRV8833PWP. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the DRV8833PWP VINT pin connected?
The VINT pin has a capacitor to GND on 36 of 43 designs, most often 2.2 µF (then 10 µF). Counted from the KiCad layouts of 43 open source designs using the DRV8833PWP.
What decoupling capacitors do designs use on the DRV8833PWP VM pin?
The VM pin has a decoupling capacitor on 28 of 43 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 43 open source designs using the DRV8833PWP.
How is the DRV8833PWP VCP pin connected?
The VCP pin has a capacitor to the supply on 22 of 43 designs, most often 10 nF (then 100 nF). Counted from the KiCad layouts of 43 open source designs using the DRV8833PWP.
What parts are used alongside the DRV8833PWP?
The AMS1117-3.3, MPU-6050, TP4056, CH224K and TP4056-42-ESOP8 appear in the most repositories here.
Which microcontrollers do boards using the DRV8833PWP use?
Most are built on STM32 (13), ESP32 (11), RP2040/RP2350 (3) and AVR/Arduino (1).
How big is a typical board using the DRV8833PWP?
The median is 73.6 × 60.5 mm, and 71% are two-layer designs.
What is the most popular open source board using the DRV8833PWP?
By GitHub stars, Langpie by langpie, with 48 stars.
Can I simulate one of these boards using the DRV8833PWP before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.