Midi keyboard
Rudra-bhardwaj·midi-keyboard-pcb·MIDI keyboard/midi keyboardd.kicad_pcb
About the Midi keyboard PCB
Midi keyboard is an open source ESP32 PCB design by Rudra-bhardwaj, published on GitHub. It is a 2-layer board measuring 82.9 × 63.3 mm, with 11 components from 6 distinct parts.
Its main chip is the Waveshare ESP32-S3-ZERO, from the ESP32 family. By type, the board carries 4 switches, 3 diodes, 1 IC and 1 connector.
It belongs with the keyboards, audio and displays & leds designs in this gallery.
Main components on the Midi keyboard
Midi keyboard bill of materials (BOM)
11 components, 6 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Waveshare ESP32-S3-ZERO | Waveshare ESP32-S3-Zero | U1 |
| 1 | touch buttons | touch pads | J1 |
| 2 | Slider | Potentiometer_Bourns_PTA1543_Single_Slide | RV3, RV4 |
| 3 | SW_Push | Kailh Choc Low-Profile Switches | SW1, SW2, SW3 |
| 1 | RotaryEncoder_Switch_MP | RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm | SW4 |
| 3 | SK6812MINI-E | LED_SK6812MINI-E_3.2x2.8mm_P1.5mm_ReverseMount | D1, D2, D3 |
Midi keyboard design files
The KiCad project lives in the Rudra-bhardwaj/midi-keyboard-pcb repository on GitHub; these links point at the commit this page was built from.
Midi keyboard: common questions
What microcontroller does the Midi keyboard use?
The Midi keyboard is built around the Waveshare ESP32-S3-ZERO, from the ESP32 family.
How big is the Midi keyboard PCB?
The Midi keyboard measures 82.9 × 63.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Midi keyboard?
11 components, from 6 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Midi keyboard design files?
From the Rudra-bhardwaj/midi-keyboard-pcb repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Midi keyboard design in my own project?
The repository has no license, so all rights stay with Rudra-bhardwaj. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Midi keyboard without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k