OpenVCU

Rujul-Rumale·OpenVCU·PCB/OpenVCU.kicad_sch

This repository ships a schematic but no board layout.

About the OpenVCU PCB

OpenVCU is an open source STM32 PCB design by Rujul-Rumale, published on GitHub under the CERN-OHL-S-2.0 license. It is a board, with 94 components from 54 distinct parts.

Its main chip is the STM32H743VIT6, from the STM32 family. Other key parts include the ICM-42688-P, FM25V02A-GTR, USBLC6-2SC6, DPS310 and AP2112K-3.3TRG1. By type, the board carries 36 capacitors, 31 resistors, 13 connectors, 7 ICs, 2 crystals and 2 diodes.

It belongs with the power & battery, sensors and robotics & motion designs in this gallery.

From the project

Open Vehicle Control Unit — one STM32H7 board for quads, planes, rovers & boats. Open KiCad schematics, CERN-OHL-S licensed.

Quad · Plane · Rover · Boat — configurable STM32H7 controller for anything that moves.

Open hardware. Designed from scratch. Built to be flashed for whatever you bolt it to.

OpenVCU is an open-source vehicle control unit built around the STM32H743VIT6 (480 MHz Cortex-M7, 2 MB flash, 1 MB RAM).

Off-the-shelf F4 flight controllers run out of headroom when you fuse RTK GPS + IMU at high rates for EKF-heavy work like 3D photogrammetry surveys. OpenVCU is my answer: H7-class compute, a clean sensor set, and one PCB that can be configured as a quad, fixed-wing, rover, or boat…

Main components on the OpenVCU

OpenVCU bill of materials (BOM)

94 components, 54 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
STM32H743VIT6
U1
1
ICM-42688-P
U2
1
FM25V02A-GTR
U3
1
USBLC6-2SC6
U4
1
DPS310
U5
1
AP2112K-3.3TRG1
U8
1
MP1584EN
TPS54360
U9
1
ABM8-272-T3
ABM8-8.000MHZ-18-D1X-T3
Y1
1
CM315D32768DZFT
Y2
1
104031-0811
J1
1
USB-C
J2
1
BM04B-GHS-TBT
GPS
J3
1
BM06B-GHS-TBT
TELEM
J4
1
BDL-108-X-X
I2C2
J5
1
BM06B-GHS-TBT
SPI2
J6
1
BM04B-GHS-TBT
SWD
J7
1
GPIO-EXP
J8
1
MOTOR
J9
1
BUZZ
J10
1
LED
J11
Show 34 more
QtyPartRefs
1
PADROW-2
J12
1
PADROW-5
J13
1
5A
F1
1
SK34
D1
1
SMBJ18A
D2
1
LPS4018-103
10uH
L1
1
L_Ferrite
L2
13
C0402C104K3RACTU
C1, C2, C5, C6, C7, C8, C9, C10 +5
1
C0402C104K3RACTU
100nF
C3
2
GRM188R61C225KE15D
C17, C23
2
GRM155R61E105KA12D
C18, C24
2
GRM1555C1H180JA01D
GRM1555C1H270JA01D
C19, C20
2
GRM1555C1H7R0DA01D
C21, C22
1
GRM21BR61A226ME51L
C26
1
C0402C104K3RACTU
C27
4
100nF
C30, C31, C32, C33
1
10nF
C34
2
100nF
C50, C53
2
10uF/50V
C51, C52
1
5.6nF
C54
2
22uF
C55, C56
2
RC0402FR-07100KL
R1, R5
4
RC0402FR-07100RL
R2, R7, R15, R21
2
RC0402FR-0710KL
4.7k
R3, R6
2
RC0402FR-075K1L
5.1k
R4, R11
10
RC0402FR-0710KL
R12, R17, R18, R19, R20, R26, R27, R28 +2
4
RC0402FR-072K2L
2.2K Ohms
R16, R22, R23, R24
1
100k
R31
1
442k
R50
1
68.1k
R51
1
196k
R52
1
100k
R53
1
19.1k
R54
1
14k
R55

OpenVCU design files

The KiCad project lives in the Rujul-Rumale/OpenVCU repository on GitHub; these links point at the commit this page was built from.

OpenVCU: common questions

What microcontroller does the OpenVCU use?

The OpenVCU is built around the STM32H743VIT6, from the STM32 family.

How many components are on the OpenVCU?

94 components, from 54 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the OpenVCU design files?

From the Rujul-Rumale/OpenVCU repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.

Can I use the OpenVCU design in my own project?

Yes, under the terms of its CERN-OHL-S-2.0 license, which Rujul-Rumale chose for the repository.

Can I test firmware for the OpenVCU without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards