Pcba triage
sabhinav3·pcba-triage·boards/rp2040_easyduino/netlist.xml
About the Pcba triage PCB
Pcba triage is an open source RP2040/RP2350 PCB design by sabhinav3, published on GitHub. It is a board, with 65 components from 19 distinct parts.
Its main chip is the RP2040, from the RP2040/RP2350 family. Other key parts include the XC6206P332MR and W25Q16JVUXIQ. By type, the board carries 17 capacitors, 15 resistors, 14 test points, 5 connectors, 4 diodes and 3 ICs.
It belongs with the test & measurement designs in this gallery.
From the project
Netlist-aware failure triage for PCBA bring-up, with a fault-injection benchmark.
Netlist-aware failure triage for PCBA bring-up, with a fault-injection benchmark.
When the first prototype boards come back from assembly, some of them don't work, and an engineer spends hours with a multimeter working out why. pcba-triage reads the board's own KiCad netlist and takes the standard bring-up measurements. It then ranks the most likely faulty nets and components and proposes the next test point to probe, within a fixed probe budget.
Main components on the Pcba triage
Pcba triage bill of materials (BOM)
65 components, 19 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XC6206P332MR | SOT-23-3 | U1 |
| 1 | RP2040 | QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U2 |
| 1 | W25Q16JVUXIQ | W25Q16JVUXIQ | U3 |
| 1 | 12MHz | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | USB_C_Receptacle_USB2.0 | USB_C_Receptacle_G-Switch_GT-USB-7010ASV | J1 |
| 2 | Conn_01x20 | PinHeader_1x20_P2.54mm_Vertical | J3, J4 |
| 1 | Conn_01x03 | PinHeader_1x03_P2.54mm_Vertical | J5 |
| 1 | Conn_01x03_MountingPin | JST_SH_BM03B-SRSS-TB_1x03-1MP_P1.00mm_Vertical | J6 |
| 4 | MountingHole | MountingHole_2.2mm_M2 | H1, H2, H3, H4 |
| 2 | SW_Push | ALPSALPINE_SKRPACE010 | SW1, SW2 |
| 14 | ~ | TestPoint_pad | TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8 +6 |
| 1 | D_Schottky | D_SOD-123 | D1 |
| 3 | LED | LED_0402_1005Metric | D2, D3, D4 |
| 11 | 100nF | C_0402_1005Metric | C1, C2, C5, C6, C7, C8, C9, C10 +3 |
| 4 | 1uF | C_0402_1005Metric | C3, C4, C13, C14 |
| 2 | 27p | C_0402_1005Metric | C16, C17 |
| 5 | 5.1k | R_0402_1005Metric | R1, R2, R3, R6, R7 |
| 2 | 27R | R_0402_1005Metric | R4, R5 |
| 8 | 1k | R_0402_1005Metric | R8, R9, R10, R11, R12, R13, R14, R15 |
Pcba triage design files
The KiCad project lives in the sabhinav3/pcba-triage repository on GitHub; these links point at the commit this page was built from.
Pcba triage: common questions
What microcontroller does the Pcba triage use?
The Pcba triage is built around the RP2040, from the RP2040/RP2350 family.
How many components are on the Pcba triage?
65 components, from 19 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Pcba triage design files?
From the sabhinav3/pcba-triage repository on GitHub, which has a netlist and the BOM; the links under Design files point to each one.
Can I use the Pcba triage design in my own project?
The repository has no license, so all rights stay with sabhinav3. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Pcba triage without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.
Similar boards
RP2040/RP2350
OSO-BOOK-C1
joeycastillo
85 × 115 mm29 parts2LCC-BY-SA-4.08.1kRP2040/RP2350
Corne cherry
foostan
277.2 × 107.5 mm164 parts2LCC-BY-4.07.7kRP2040/RP2350
Corne chocolate
foostan
277.2 × 107.5 mm164 parts2LCC-BY-4.07.7kRP2040/RP2350
Jitx design
gusmanb
55.5 × 65 mm26 parts4LGPL-3.05.0kRP2040/RP2350
LogicAnalyzer
gusmanb
57 × 55.2 mm6 parts2LGPL-3.05.0kRP2040/RP2350
Main
google
98 × 71 mm102 parts2LApache-2.02.9k