Arduin o punch
sakhnik·arduin-o-punch·arduino/pcb/aop/aop.kicad_pcb
About the Arduin o punch PCB
Arduin o punch is an open source ESP32 PCB design by sakhnik, published on GitHub under the GPL-2.0 license. It is a 2-layer board measuring 45 × 55 mm, with 19 components from 18 distinct parts.
Its main chip is the ESP32-C3_SUPERMINI_TH, from the ESP32 family. Other key parts include the DS3231M. By type, the board carries 5 resistors, 3 capacitors, 2 ICs, 2 switches, 2 test points and 1 module.
From the project
Arduino-based punching for orienteering
Arduino-based punching for orienteering with Mifare NFC cards.
In development. The progress can be followed in the YouTube playlist: Arduin-o-punch.

Main components on the Arduin o punch
Arduin o punch bill of materials (BOM)
19 components, 18 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3_SUPERMINI_TH | MODULE_ESP32-C3_SUPERMINI_TH | U1 |
| 1 | DS3231M | SOIC-16W_7.5x10.3mm_P1.27mm | U2 |
| 1 | RFID-RC522 ~ | RFID-RC522_1 | M1 |
| 1 | AO4435 | SOIC127P600X175-8N | Q1 |
| 1 | UART | PinHeader_1x03_P2.54mm_Vertical | J1 |
| 1 | Buzzer | Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | SW_Push | R_Axial_DIN0207_L6.3mm_D2.5mm_P5.08mm_Vertical | SW1 |
| 1 | SW_Push | R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | SW2 |
| 1 | BAT+ | TestPoint_THTPad_4.0x4.0mm_Drill2.0mm | TP1 |
| 1 | BAT– | TestPoint_THTPad_4.0x4.0mm_Drill2.0mm | TP2 |
| 1 | LED | LED_1206_3216Metric | D1 |
| 1 | 470uF | CP_Radial_D8.0mm_P3.50mm | C1 |
| 1 | 1uF | C_1206_3216Metric | C2 |
| 1 | 100nF | C_1206_3216Metric | C3 |
| 1 | 100K | R_1206_3216Metric | R1 |
| 1 | 1K | R_1206_3216Metric | R2 |
| 1 | 100 | R_1206_3216Metric | R3 |
| 2 | 4K7 | R_1206_3216Metric | R4, R5 |
Arduin o punch design files
The KiCad project lives in the sakhnik/arduin-o-punch repository on GitHub; these links point at the commit this page was built from.
- Layoutarduino/pcb/aop/aop.kicad_pcb
- Schematicarduino/pcb/aop/aop.kicad_sch
Arduin o punch: common questions
What microcontroller does the Arduin o punch use?
The Arduin o punch is built around the ESP32-C3_SUPERMINI_TH, from the ESP32 family.
How big is the Arduin o punch PCB?
The Arduin o punch measures 45 × 55 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Arduin o punch?
19 components, from 18 distinct parts. The full bill of materials is listed on this page.
Where can I download the Arduin o punch design files?
From the sakhnik/arduin-o-punch repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Arduin o punch design in my own project?
Yes, under the terms of its GPL-2.0 license, which sakhnik chose for the repository.
Can I test firmware for the Arduin o punch without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k