Lidar 2
Slenderman00·Lidar·lidar 2/lidar 2.kicad_pcb
About the Lidar 2 PCB
Lidar 2 is an open source ESP32 PCB design by Slenderman00, published on GitHub. It is a 2-layer board measuring 40 × 85.1 mm, with 19 components from 15 distinct parts.
Its main chip is the ESP32-S3-MINI-1, from the ESP32 family. Other key parts include the LM1117DT-3.3, LM1117S-5.0 and DRV5055A2xDBZxQ1. By type, the board carries 5 ICs, 5 connectors, 4 capacitors, 2 switches, 2 resistors and 1 transistor.
Main components on the Lidar 2
Lidar 2 bill of materials (BOM)
19 components, 15 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM1117DT-3.3 | TO-252-3_TabPin2 | U1 |
| 1 | LM1117S-5.0 | TO-263-3_TabPin2 | U2 |
| 1 | ESP32-S3-MINI-1 | ESP32-S3-MINI-1 | U3 |
| 1 | ~ | TMF8805 | U4 |
| 1 | DRV5055A2xDBZxQ1 | SOT-23 | U6 |
| 1 | BC847 | SOT-23 | Q2 |
| 1 | USB_C_Receptacle_USB2.0 | USB_C_Receptacle_GCT_USB4110 | J1 |
| 1 | Motor | PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | UART | PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | JTAG | PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | VIN | PinSocket_1x02_P2.54mm_Vertical | J5 |
| 1 | BOOT | SW_Push_1P1T_NO_6x6mm_H9.5mm | SW1 |
| 1 | RESET | SW_Push_1P1T_NO_6x6mm_H9.5mm | SW2 |
| 4 | X7R 0.1 μF 6.3 V | C_0402_1005Metric | C1, C2, C3, C4 |
| 2 | 1Mohm | R_0805_2012Metric | R1, R2 |
Lidar 2 design files
The KiCad project lives in the Slenderman00/Lidar repository on GitHub; these links point at the commit this page was built from.
- Layoutlidar 2/lidar 2.kicad_pcb
- Schematiclidar 2/lidar 2.kicad_sch
Lidar 2: common questions
What microcontroller does the Lidar 2 use?
The Lidar 2 is built around the ESP32-S3-MINI-1, from the ESP32 family.
How big is the Lidar 2 PCB?
The Lidar 2 measures 40 × 85.1 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Lidar 2?
19 components, from 15 distinct parts. The full bill of materials is listed on this page.
Where can I download the Lidar 2 design files?
From the Slenderman00/Lidar repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Lidar 2 design in my own project?
The repository has no license, so all rights stay with Slenderman00. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Lidar 2 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Lidar
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k