Lidar 2 round
Slenderman00·Lidar·lidar 2/lidar 2 round.kicad_pcb
About the Lidar 2 round PCB
Lidar 2 round is an open source ESP32 PCB design by Slenderman00, published on GitHub. It is a 2-layer board measuring 60 × 60 mm, with 22 components from 17 distinct parts.
Its main chip is the ESP32-S3-MINI-1, from the ESP32 family. Other key parts include the DRV5055A2xDBZxQ1. By type, the board carries 4 ICs, 4 connectors, 4 capacitors, 4 resistors, 2 switches and 1 transistor.
Main components on the Lidar 2 round
Lidar 2 round bill of materials (BOM)
22 components, 17 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ~ | TMF8805 | U2 |
| 1 | ~ | LC8805B-1515 | U3 |
| 1 | DRV5055A2xDBZxQ1 | SOT-23 | U4 |
| 1 | ESP32-S3-MINI-1 | ESP32-S3-MINI-1 | U5 |
| 1 | BC847 | SOT-23 | Q1 |
| 1 | UART | PinHeader_1x04_P2.54mm_Horizontal | J1 |
| 1 | Motor | PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | JTAG | PinHeader_1x04_P2.54mm_Horizontal | J3 |
| 1 | VIN | PinSocket_1x02_P2.54mm_Horizontal | J4 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | +3v3 |
| 1 | AMS1117-5.0 | SOT-223-3_TabPin2 | +5V |
| 1 | BOOT | SW_Push_SPST_NO_Alps_SKRK | SW1 |
| 1 | RESET | SW_Push_SPST_NO_Alps_SKRK | SW2 |
| 1 | MBR0520 | D_SOD-123 | D1 |
| 4 | X7R 0.1 μF 6.3 V | C_0402_1005Metric | C1, C2, C3, C4 |
| 2 | 1Mohm | R_0402_1005Metric | R1, R2 |
| 2 | 1 Mohm | R_0402_1005Metric | R3, R4 |
Lidar 2 round design files
The KiCad project lives in the Slenderman00/Lidar repository on GitHub; these links point at the commit this page was built from.
Lidar 2 round: common questions
What microcontroller does the Lidar 2 round use?
The Lidar 2 round is built around the ESP32-S3-MINI-1, from the ESP32 family.
How big is the Lidar 2 round PCB?
The Lidar 2 round measures 60 × 60 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Lidar 2 round?
22 components, from 17 distinct parts. The full bill of materials is listed on this page.
Where can I download the Lidar 2 round design files?
From the Slenderman00/Lidar repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Lidar 2 round design in my own project?
The repository has no license, so all rights stay with Slenderman00. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Lidar 2 round without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Lidar
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k