RFID reader125kHz

SolderedElectronics·125kHz-RFID-UART-board-hardware-design·CAD/V1.0.0/RFID_reader125kHz.kicad_pcb

RFID reader125kHz PCB layout, top view — open source AVR/Arduino board by SolderedElectronics

About the RFID reader125kHz PCB

RFID reader125kHz is an open source AVR/Arduino PCB design by SolderedElectronics, published on GitHub under the TAPR-OHL-1.0 license. It is a 2-layer board measuring 38 × 38 mm, with 63 components from 31 distinct parts.

Its main chip is the ATTINY1604-SSNR, from the AVR/Arduino family. Other key parts include the NMOS-DUAL, LM358DR and TPS613222A. By type, the board carries 20 resistors, 16 capacitors, 7 relays, 5 diodes, 4 ICs and 4 jumpers.

From the project

Hardware design, BOM, gerbers and 3D files for 125kHz-RFID-UART-board designed by Soldered Electronics.

RFID is a type of communication in which information is transmitted wirelessly (Wikipedia article). Today, it is becoming increasingly popular and can be found in numerous and various cards: driving licenses, access control to buildings, public transportation, etc.

RFID readers come in many forms and variants. This reader, from our production, enables easy connection to a microcontroller, thereby opening up possibilities for developing various projects based on RFID technology. The breakout comes in two versions, and depending on the version, it is programmed and ready for communication via…

RFID reader125kHz, from the project README
From the project README

Main components on the RFID reader125kHz

RFID reader125kHz bill of materials (BOM)

63 components, 31 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ATTINY1604-SSNR
U1
1
NMOS-DUAL
U2
1
LM358DR
U3
1
TPS613222A
U4
1
NPN
Q1
1
PNP
Q2
4
HOLE_3.2MM
HOLE_3.2mm
H1, H2, H3, H4
2
SMD_JUMPER_3_PAD_TRACE
JP1, JP2
2
SMD-JUMPER-CONNECTED_TRACE_SLODERMASK
JP3, JP4
1
S2B-XH-A
K1
1
HEADER-UPDI
K2
2
easyC-SMD
K3, K5
1
HEADER_MALE_5X1
K4
1
HEADER_MALE_4X1
K6
1
DSHP03TS-S
K7
3
M4_DIODA
D1, D2, D3
2
blue
D4, D5
1
DFE201612E-2R2M=P2
L1
5
100N
100n
C1, C2, C9, C10, C15
5
C0603C102K5RACTU
C3, C4, C5, C6, C8
Show 11 more
QtyPartRefs
2
CL21A475KBQNNNE
C7, C12
2
CL10A226MP8NUNE
C11, C13
1
C1608X7S1A475K080AC
C14
1
10U
10u
C16
7
1K
R1, R2, R11, R14, R17, R18, R19
4
10K
R3, R4, R6, R7
1
220
R5
1
10
R8
4
1M
R9, R10, R13, R15
1
100K
R12
2
2K2
2k2
R16, R20

RFID reader125kHz design files

The KiCad project lives in the SolderedElectronics/125kHz-RFID-UART-board-hardware-design repository on GitHub; these links point at the commit this page was built from.

RFID reader125kHz: common questions

What microcontroller does the RFID reader125kHz use?

The RFID reader125kHz is built around the ATTINY1604-SSNR, from the AVR/Arduino family.

How big is the RFID reader125kHz PCB?

The RFID reader125kHz measures 38 × 38 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the RFID reader125kHz?

63 components, from 31 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the RFID reader125kHz design files?

From the SolderedElectronics/125kHz-RFID-UART-board-hardware-design repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the RFID reader125kHz design in my own project?

Yes, under the terms of its TAPR-OHL-1.0 license, which SolderedElectronics chose for the repository.

Can I test firmware for the RFID reader125kHz without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in 125kHz-RFID-UART-board-hardware-design

Similar boards