19 open source boards using the LM358DR
Real designs built with the LM358DR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
UltiCore-V1-PLC
paulmartinezcuenta
110 × 90 mm192 parts4LMIT1STM32
BIRDS-X
AlbertaSat
79 × 81 mm146 parts4LCERN-OHL-P-2.01STM32
PCB DRONE C8
ArduProject
102 × 49 mm140 parts4LMIT1AVR/Arduino
InverterBoostConverter
datacrystals
450 × 150 mm225 parts2LNo license0ESP32
Sunrise clock main board
atoomnetmarc
160 × 106.7 mm124 parts2LApache-2.00AVR/Arduino
125kHz RFID board
SolderedElectronics
38 × 38 mm68 parts2LTAPR-OHL-1.00AVR/Arduino
125kHz RFID board
SolderedElectronics
38 × 38 mm68 parts2LTAPR-OHL-1.00AVR/Arduino
125kHz RFID board
SolderedElectronics
38 × 38 mm68 parts2LTAPR-OHL-1.00ESP32
PCB SALUS V3
LeoSole423
100 × 100 mm63 parts2LNo license0- schematic only · 5 parts
CertifyMe
jdharcourt
5 partsNo license0 Protected programmable current output
dshills
70 × 50 mm15 parts2LMIT7AVR/Arduino
125kHz RFID I2C board with easyC
SolderedElectronics
38 × 38 mm68 parts2LTAPR-OHL-1.00AVR/Arduino
125kHz RFID UART board
SolderedElectronics
38 × 38 mm68 parts2LTAPR-OHL-1.00AVR/Arduino
125kHz RFID I2C board with easyC
SolderedElectronics
38 × 38 mm68 parts2LTAPR-OHL-1.00AVR/Arduino
RFID reader125kHz
SolderedElectronics
38 × 38 mm63 parts2LTAPR-OHL-1.00AVR/Arduino
RFID reader125kHz
SolderedElectronics
38 × 38 mm63 parts2LTAPR-OHL-1.00AVR/Arduino
RFID reader125kHz
SolderedElectronics
38 × 38 mm63 parts2LTAPR-OHL-1.00AVR/Arduino
DynamicBrakeGrid
datacrystals
350 × 150 mm151 parts4LNo license0Analog out
atopile
16 × 5 mm8 parts2LMIT29
How designs wire the LM358DR
Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the LM358DR connects to, and the resistors, capacitors and other passives placed on it.
- The OUTA pin has a series resistor on 8 of 11 designs, most often 4.7 kΩ (then 1 MΩ).
- The INA- pin has a series resistor on 8 of 11 designs, most often 220 Ω (then 1 MΩ).
- The VDD pin has a decoupling capacitor on 8 of 11 designs, most often 100 nF.
- The INA+ pin has a series resistor on 7 of 11 designs, most often 100 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| OUTApin 1 | Connected to: Signal 100% |
|
| INA-pin 2 | Connected to: Signal 100% |
|
| INA+pin 3 | Connected to: Signal 91% |
|
| VSSpin 4 | Connected to: GND 91% | — |
| INB+pin 5 | Connected to: Signal 64% · not connected 18% · GND 18% |
|
| INB-pin 6 | Connected to: Signal 64% · not connected 36% |
|
| OUTBpin 7 | Connected to: The microcontroller 27% · not connected 36% |
|
| VDDpin 8 | Connected to: 3.3V 64% · a signal 27% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Analog out by atopile, Protected programmable current output by dshills, BIRDS-X-PCB by AlbertaSat and PCB DRONE C8 by ArduProject.
The LM358DR in open source designs
The gallery holds 19 open source boards using the LM358DR from 12 GitHub repositories; a typical one measures about 38 × 38 mm and carries around 68 components.
78% are two-layer designs, the rest use four layers or more, and 79% carry an open source license.
The most starred is Analog out by atopile.
Parts used alongside the LM358DR
Microcontrollers on boards using the LM358DR
What boards using the LM358DR are built for
LM358DR: common questions
Where can I find a LM358DR reference design?
Each of the 19 boards on this page is a real design using the LM358DR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the LM358DR OUTA pin?
The OUTA pin has a series resistor on 8 of 11 designs, most often 4.7 kΩ (then 1 MΩ). Counted from the KiCad layouts of 11 open source designs using the LM358DR.
What resistor goes on the LM358DR INA- pin?
The INA- pin has a series resistor on 8 of 11 designs, most often 220 Ω (then 1 MΩ). Counted from the KiCad layouts of 11 open source designs using the LM358DR.
What decoupling capacitors do designs use on the LM358DR VDD pin?
The VDD pin has a decoupling capacitor on 8 of 11 designs, most often 100 nF. Counted from the KiCad layouts of 11 open source designs using the LM358DR.
What parts are used alongside the LM358DR?
The ATTINY1604-SSNR, NMOS-DUAL and TPS613222A appear in the most repositories here.
Which microcontrollers do boards using the LM358DR use?
Most are built on AVR/Arduino (11), ESP32 (3) and STM32 (2).
How big is a typical board using the LM358DR?
The median is 38 × 38 mm, and 78% are two-layer designs.
What is the most popular open source board using the LM358DR?
By GitHub stars, Analog out by atopile, with 29 stars.
Can I simulate one of these boards using the LM358DR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.