13 open source boards using the ATTINY1604-SSNR
Real designs built with the ATTINY1604-SSNR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
GNSS GPS L86-M33 breakout with easyC
SolderedElectronics
54 × 38 mm31 parts2LTAPR-OHL-1.02AVR/Arduino
GNSS GPS L86-M33 breakout with easyC
SolderedElectronics
54 × 38 mm31 parts2LTAPR-OHL-1.01AVR/Arduino
125kHz RFID board
SolderedElectronics
38 × 38 mm68 parts2LTAPR-OHL-1.00AVR/Arduino
125kHz RFID board
SolderedElectronics
38 × 38 mm68 parts2LTAPR-OHL-1.00AVR/Arduino
125kHz RFID board
SolderedElectronics
38 × 38 mm68 parts2LTAPR-OHL-1.00AVR/Arduino
GNSS GPS L86-M33 breakout with easyC panel
SolderedElectronics
162 × 164 mm31 parts2LTAPR-OHL-1.02AVR/Arduino
GNSS GPS L86-M33 breakout with easyC panel
SolderedElectronics
162 × 164 mm31 parts2LTAPR-OHL-1.01AVR/Arduino
125kHz RFID I2C board with easyC
SolderedElectronics
38 × 38 mm68 parts2LTAPR-OHL-1.00AVR/Arduino
125kHz RFID I2C board with easyC
SolderedElectronics
38 × 38 mm68 parts2LTAPR-OHL-1.00AVR/Arduino
125kHz RFID UART board
SolderedElectronics
38 × 38 mm68 parts2LTAPR-OHL-1.00AVR/Arduino
RFID reader125kHz
SolderedElectronics
38 × 38 mm63 parts2LTAPR-OHL-1.00AVR/Arduino
RFID reader125kHz
SolderedElectronics
38 × 38 mm63 parts2LTAPR-OHL-1.00AVR/Arduino
RFID reader125kHz
SolderedElectronics
38 × 38 mm63 parts2LTAPR-OHL-1.00
How designs wire the ATTINY1604-SSNR
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the ATTINY1604-SSNR connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 5 of 5 designs, most often 100 nF (then 10 µF).
- The PA1 pin has a series resistor on 5 of 5 designs, most often 10 kΩ (then 1 kΩ).
- The PB3 pin has a pull-up to 3.3V on 3 of 5 designs, most often 10 kΩ.
- The PB2 pin has a pull-up to 3.3V on 3 of 5 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VCCpin 1 | Connected to: 3.3V 100% |
|
| PA4pin 2 | Connected to: Signal 100% |
|
| PA5pin 3 | Connected to: L86-M33 40% |
|
| PB3pin 6 | Connected to: NMOS-DUAL 60% |
|
| PB2pin 7 | Connected to: NMOS-DUAL 60% |
|
| PB1pin 8 | Connected to: NMOS-DUAL 60% |
|
| PB0pin 9 | Connected to: NMOS-DUAL 60% |
|
| PA1pin 11 | Connected to: LM358DR 60% |
|
| PA2pin 12 | Connected to: Not connected 60% · a signal 40% |
|
| PA3pin 13 | Connected to: L86-M33 40% |
|
| GNDpin 14 | Connected to: GND 100% | — |
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include GNSS GPS L86-M33 breakout with easyC by SolderedElectronics, GNSS GPS L86-M33 breakout with easyC by SolderedElectronics, 125kHz RFID board by SolderedElectronics and 125kHz RFID board by SolderedElectronics.
The ATTINY1604-SSNR in open source designs
The gallery holds 13 open source boards using the ATTINY1604-SSNR from 5 GitHub repositories; a typical one measures about 38 × 38 mm and carries around 63 components.
100% are two-layer designs, the rest use four layers or more, and 100% carry an open source license.
The most starred is GNSS GPS L86-M33 breakout with easyC panel by SolderedElectronics.
Parts used alongside the ATTINY1604-SSNR
Microcontrollers on boards using the ATTINY1604-SSNR
What boards using the ATTINY1604-SSNR are built for
ATTINY1604-SSNR: common questions
Where can I find a ATTINY1604-SSNR reference design?
Each of the 13 boards on this page is a real design using the ATTINY1604-SSNR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the ATTINY1604-SSNR VCC pin?
The VCC pin has a decoupling capacitor on 5 of 5 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 5 open source designs using the ATTINY1604-SSNR.
What resistor goes on the ATTINY1604-SSNR PA1 pin?
The PA1 pin has a series resistor on 5 of 5 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 5 open source designs using the ATTINY1604-SSNR.
What pull-up resistor is used on the ATTINY1604-SSNR PB3 pin?
The PB3 pin has a pull-up to 3.3V on 3 of 5 designs, most often 10 kΩ. Counted from the KiCad layouts of 5 open source designs using the ATTINY1604-SSNR.
What parts are used alongside the ATTINY1604-SSNR?
The LM358DR, NMOS-DUAL, TPS613222A and L86-M33 appear in the most repositories here.
Which microcontrollers do boards using the ATTINY1604-SSNR use?
Most are built on AVR/Arduino (13).
How big is a typical board using the ATTINY1604-SSNR?
The median is 38 × 38 mm, and 100% are two-layer designs.
What is the most popular open source board using the ATTINY1604-SSNR?
By GitHub stars, GNSS GPS L86-M33 breakout with easyC panel by SolderedElectronics, with 2 stars.
Can I simulate one of these boards using the ATTINY1604-SSNR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.