CAN-Transceiver-MCP2518-board hardware design
SolderedElectronics·CAN-Transceiver-MCP2518-board-hardware-design·CAD/V1.1.1/CAN_MCP2518FDT.kicad_pcb
About the CAN-Transceiver-MCP2518-board hardware design
CAN-Transceiver-MCP2518-board hardware design is an open source PCB design by SolderedElectronics, published on GitHub under the TAPR-OHL-1.0 license. It is a 2-layer board measuring 38 × 22 mm, with 20 components from 15 distinct parts.
Other key parts include the SE5218, MCP2518FDT-E/SL and ATA6561-GAQW-N. By type, the board carries 6 capacitors, 3 ICs, 3 relays, 2 jumpers, 2 resistors and 1 crystal.
It belongs with the rf & radio and dev boards & breakouts designs in this gallery.
From the project
Hardware design, BOM, gerbers and 3D files for CAN-Transceiver-MCP2518-board designed by Soldered Electronics.
CAN Transceiver (Controller Area Network) is a network technology that enables fast communication between microcontrollers, and is the most commonly used standard in cars. Our CAN breakout uses an MCP2518FD CAN whose communication between microcontrollers takes place on SPI protocol. In addition there is a CAN transceiver. This breakout allows use of both standards (CAN 2.0B and CAN Flexible Data (FD)). Access to the CAN bus is possible via CANH and CANL pins on the screw terminal. The 120ohm terminator resistor is also located on the board and can be connected to a jumper.

Main components on the CAN-Transceiver-MCP2518-board hardware design
CAN-Transceiver-MCP2518-board hardware design bill of materials (BOM)
20 components, 15 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | SE5218 | SOT-23-5 | U1 |
| 1 | MCP2518FDT-E/SL | SOIC-14 | U2 |
| 1 | ATA6561-GAQW-N | SOIC−8 | U3 |
| 1 | 40MHZ 40MHz | KRISTAL_3225__4_PAD | X1 |
| 2 | HOLE_3.2MM HOLE_3.2mm | HOLE_3.2mm | H1, H2 |
| 1 | SMD_JUMPER | SMD_JUMPER | JP1 |
| 1 | SMD-JUMPER-CONNECTED_TRACE_SLODERMASK | SMD-JUMPER-CONNECTED_TRACE_SLODERMASK | JP2 |
| 2 | HEADER_MALE_6X1 | HEADER_MALE_6X1 | K1, K2 |
| 1 | TERMINAL_KF235-5.0-2P | TERMINAL_KF235-5.0-2P | K3 |
| 1 | purple | 0402LED | D1 |
| 2 | 22PF 22pF | 0603C | C1, C2 |
| 2 | 2.2UF 2.2uF | 0603C | C3, C5 |
| 2 | 0.1UF 0.1uF | 0603C | C4, C6 |
| 1 | 120R | 0603R | R1 |
| 1 | 2K2 2k2 | 0402R | R2 |
CAN-Transceiver-MCP2518-board hardware design design files
The KiCad project lives in the SolderedElectronics/CAN-Transceiver-MCP2518-board-hardware-design repository on GitHub; these links point at the commit this page was built from.
CAN-Transceiver-MCP2518-board hardware design: common questions
How big is the CAN-Transceiver-MCP2518-board hardware design?
The CAN-Transceiver-MCP2518-board hardware design measures 38 × 22 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the CAN-Transceiver-MCP2518-board hardware design?
20 components, from 15 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the CAN-Transceiver-MCP2518-board hardware design design files?
From the SolderedElectronics/CAN-Transceiver-MCP2518-board-hardware-design repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the CAN-Transceiver-MCP2518-board hardware design design in my own project?
Yes, under the terms of its TAPR-OHL-1.0 license, which SolderedElectronics chose for the repository.
Similar boards
Breakout 112pin Connector
rusefi
174 × 58 mm39 parts2LGPL-3.01.2kEecv breakout
rusefi
140.8 × 53.7 mm9 parts4LGPL-3.01.2kBreakout 60pin EEC-IV
rusefi
139.7 × 62.2 mm15 parts2LGPL-3.01.2k134pin 7-967288-1
rusefi
139.7 × 73.7 mm38 parts2LGPL-3.01.2k88 Pin Vag Breakout
rusefi
142 × 58 mm91 parts2LGPL-3.01.2kRj45 breakout
rene-dev
15.2 × 53.8 mm3 parts2LGPL-3.0979