18 open source boards using the ATA6561-GAQW-N
Real designs built with the ATA6561-GAQW-N, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
CAN-Transceiver-MCP2518-board hardware design
SolderedElectronics
38 × 22 mm20 parts2LTAPR-OHL-1.09Esc w26
Electrium-Mobility
125 × 80 mm165 parts4LMIT4STM32
BMS 1
lbrosnan1
105.2 × 55.3 mm110 parts2LNo license2Soldered-CAN-Transceiver-MCP2518-board hardware design
test-gh-syncer2
22 × 38 mm20 parts2LTAPR-OHL-1.02STM32
Stm32-can do dev board
kurtjd
54 × 78 mm49 parts2LMIT1Glr pcb display can shield
green-lion-racing
60.4 × 98.7 mm28 parts2LGPL-3.01STM32
ControlPanelV3S
bartkepl
120 × 75 mm300 parts4LMIT0ESP32
ESP32-S3 Dev Board
hw-tinkerers
123.5 × 56.5 mm146 parts4LNo license0STM32
Autotrainer Pellet Module
Mouse-GYM
114.3 × 108 mm140 parts4LNo license0RP2040/RP2350
FligthComputers
ManuelRao
50 × 72.5 mm131 parts4LNo license0ESP32
Main
VeeT23
60 × 40 mm52 parts2LGPL-3.00STM32
Ramn
ToyotaInfoTech
85.6 × 54 mm96 parts2LCC-BY-SA-4.0280STM32
Pneu pwr brd 11 19 25
lbrosnan1
65 × 65 mm75 parts4LNo license2STM32
Magnet Module
Mouse-GYM
71 × 89 mm117 parts4LNo license0STM32
Misc Control Card v4
lbrosnan1
99.9 × 62 mm57 parts2LNo license2Jetson AGX Orin CAN Adapter
Mouse-GYM
63 × 23.5 mm18 parts2LNo license0STM32
Misc Control Card (1) (2)
lbrosnan1
99.9 × 62 mm42 parts4LNo license2STM32
Thruster Control Card
lbrosnan1
100 × 61.9 mm19 parts4LNo license2
How designs wire the ATA6561-GAQW-N
Read from the KiCad layouts of 12 open source designs, one per repository: what each pin of the ATA6561-GAQW-N connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 12 of 12 designs, most often 100 nF (then 22 µF).
- The VIO pin has a decoupling capacitor on 9 of 12 designs, most often 100 nF (then 2.2 µF).
- The CANL pin has a series resistor on 8 of 12 designs, most often 120 Ω (then 60 Ω).
- The CANH pin has a series resistor on 6 of 12 designs, most often 60 Ω (then 0 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 2 | Connected to: GND 100% | — |
| VCCpin 3 | Connected to: 5V 92% |
|
| VIOpin 5 | Connected to: 3.3V 92% |
|
| CANLpin 6 | Connected to: A connector 58% |
|
| CANHpin 7 | Connected to: A connector 58% |
|
| STBYpin 8 | Connected to: GND 42% · not connected 17% · a signal 42% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Ramn by ToyotaInfoTech, CAN-Transceiver-MCP2518-board hardware design by SolderedElectronics, Esc w26 by Electrium-Mobility and BMS 1 by lbrosnan1.
The ATA6561-GAQW-N in open source designs
The gallery holds 18 open source boards using the ATA6561-GAQW-N from 12 GitHub repositories; a typical one measures about 78.3 × 62 mm and carries around 66 components.
50% are two-layer designs, the rest use four layers or more, and 44% carry an open source license.
The most starred is Ramn by ToyotaInfoTech.
Parts used alongside the ATA6561-GAQW-N
Microcontrollers on boards using the ATA6561-GAQW-N
What boards using the ATA6561-GAQW-N are built for
ATA6561-GAQW-N: common questions
Where can I find a ATA6561-GAQW-N reference design?
Each of the 18 boards on this page is a real design using the ATA6561-GAQW-N. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the ATA6561-GAQW-N VCC pin?
The VCC pin has a decoupling capacitor on 12 of 12 designs, most often 100 nF (then 22 µF). Counted from the KiCad layouts of 12 open source designs using the ATA6561-GAQW-N.
What decoupling capacitors do designs use on the ATA6561-GAQW-N VIO pin?
The VIO pin has a decoupling capacitor on 9 of 12 designs, most often 100 nF (then 2.2 µF). Counted from the KiCad layouts of 12 open source designs using the ATA6561-GAQW-N.
What resistor goes on the ATA6561-GAQW-N CANL pin?
The CANL pin has a series resistor on 8 of 12 designs, most often 120 Ω (then 60 Ω). Counted from the KiCad layouts of 12 open source designs using the ATA6561-GAQW-N.
Which microcontrollers do boards using the ATA6561-GAQW-N use?
Most are built on STM32 (10), ESP32 (2) and RP2040/RP2350 (1).
How big is a typical board using the ATA6561-GAQW-N?
The median is 78.3 × 62 mm, and 50% are two-layer designs.
What is the most popular open source board using the ATA6561-GAQW-N?
By GitHub stars, Ramn by ToyotaInfoTech, with 280 stars.
Can I simulate one of these boards using the ATA6561-GAQW-N before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.