Hall effect sensor easyC
SolderedElectronics·Hall-effect-sensor-breakout-with-digital-output---easyC-hardware-design·CAD/V1.0.0/Hall_effect_sensor_easyC.kicad_pcb
About the Hall effect sensor easyC PCB
Hall effect sensor easyC is an open source AVR/Arduino PCB design by SolderedElectronics, published on GitHub under the TAPR-OHL-1.0 license. It is a 2-layer board measuring 22 × 22 mm, with 12 components from 8 distinct parts.
Its main chip is the ATTINY404-SSNR, from the AVR/Arduino family. Other key parts include the SI7201-B-06-IV. By type, the board carries 4 relays, 2 ICs, 2 capacitors and 2 resistors.
It belongs with the sensors and dev boards & breakouts designs in this gallery.
From the project
Hardware design, BOM, gerbers and 3D files for Hall-effect-sensor-breakout-with-digital-output-&-easyC designed by Soldered Electronics.
All Soldered Electronics hardware designed in KiCAD, and repositories are organized in the following way:
- CAD folder - contains KiCAD files (Schematics, Board, Panel Board), sorted by version. Change log lists all changes between versions. - OUTPUTS - contains useful files, such as Bill of Materials (BOM), PDF of schematics, 3D .step file of the board and gerber files, sorted by version. - OUTPUTS -> Compliance - Certificates and useful legal stuff.

Main components on the Hall effect sensor easyC
Hall effect sensor easyC bill of materials (BOM)
12 components, 8 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | SI7201-B-06-IV | SOT-23-3 | U1 |
| 1 | ATTINY404-SSNR | SOIC-14 | U2 |
| 2 | HOLE_3.2MM HOLE_3.2mm | HOLE_3.2mm | H1, H2 |
| 2 | easyC-SMD | easyC-connector | K1, K3 |
| 1 | HEADER-UPDI | HEADER-UPDI | K2 |
| 1 | DSHP03TS-S | DSHP03TS-S | K4 |
| 2 | 0.1UF 0.1uF | 0603C | C1, C2 |
| 2 | 10K 10k | 0603R | R1, R2 |
Hall effect sensor easyC design files
The KiCad project lives in the SolderedElectronics/Hall-effect-sensor-breakout-with-digital-output---easyC-hardware-design repository on GitHub; these links point at the commit this page was built from.
Hall effect sensor easyC: common questions
What microcontroller does the Hall effect sensor easyC use?
The Hall effect sensor easyC is built around the ATTINY404-SSNR, from the AVR/Arduino family.
How big is the Hall effect sensor easyC PCB?
The Hall effect sensor easyC measures 22 × 22 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Hall effect sensor easyC?
12 components, from 8 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Hall effect sensor easyC design files?
From the SolderedElectronics/Hall-effect-sensor-breakout-with-digital-output---easyC-hardware-design repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Hall effect sensor easyC design in my own project?
Yes, under the terms of its TAPR-OHL-1.0 license, which SolderedElectronics chose for the repository.
Can I test firmware for the Hall effect sensor easyC without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in Hall-effect-sensor-breakout-with-digital-output---easyC-hardware-design
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k