Mobrob
Spacha·mobrob·robot_hw/mobrob_v1.0/mobrob.kicad_pcb
About the Mobrob PCB
Mobrob is an open source ESP32 PCB design by Spacha, published on GitHub. It is a 4-layer board measuring 100 × 54 mm, with 27 components from 17 distinct parts.
Its main chip is the ESP32_1, from the ESP32 family. Other key parts include the L293D and L7805. By type, the board carries 10 diodes, 9 connectors, 4 capacitors, 2 ICs and 2 resistors.
It belongs with the robotics & motion, iot & wireless and power & battery designs in this gallery.
From the project
Obstacle detection and avoidance Room mapping (explore mode?) Manual control (throttle + steer) For example, through browser-based GUI Automatic navigation (A to B) (after exploring space?) Complete more complex tasks like fetch an item? Charging capability preferable (e.g. MCP73
Obstacle detection and avoidance Room mapping (explore mode?) Manual control (throttle + steer) For example, through browser-based GUI Automatic navigation (A to B) (after exploring space?) Complete more complex tasks like fetch an item? Charging capability preferable (e.g. MCP73831) https://www.youtube.com/watch?v=GRd9uTwg7r4&abchannel=MicroTypeEngineering https://www.youtube.com/watch?v=TyaW8ZKumno&ab_channel=PlumPot
Main components on the Mobrob
Mobrob bill of materials (BOM)
27 components, 17 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | L293D | DIP-16_W7.62mm | U1 |
| 1 | L7805 | TO-220-3_Vertical | U2 |
| 1 | RMOTOR | TerminalBlock_Phoenix_PT-1,5-2-3.5-H_1x02_P3.50mm_Horizontal | J1 |
| 1 | LMOTOR | TerminalBlock_Phoenix_PT-1,5-2-3.5-H_1x02_P3.50mm_Horizontal | J2 |
| 1 | POWER | TerminalBlock_Phoenix_PT-1,5-2-3.5-H_1x02_P3.50mm_Horizontal | J3 |
| 1 | ESP32_1 | PinSocket_1x15_P2.54mm_Vertical | J4 |
| 1 | ESP32_2 | PinSocket_1x15_P2.54mm_Vertical | J5 |
| 2 | LHALL | PinHeader_1x03_P2.54mm_Vertical | J6, J7 |
| 1 | IMU | PinSocket_1x08_P2.54mm_Vertical | J8 |
| 1 | UT | PinHeader_1x04_P2.54mm_Vertical | J9 |
| 8 | M7 | D_SMA_Handsoldering | D1, D2, D3, D4, D5, D6, D7, D8 |
| 1 | LED_STATUS | LED_D5.0mm | D9 |
| 1 | LED_POWER | LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D10 |
| 1 | 0.22UF 0.22uF | CP_Radial_D10.0mm_P5.00mm | C1 |
| 1 | 0.1UF 0.1uF | CP_Radial_D10.0mm_P5.00mm | C2 |
| 2 | 0.1UF 0.1uF | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C3, C4 |
| 2 | 150 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2 |
Mobrob design files
The KiCad project lives in the Spacha/mobrob repository on GitHub; these links point at the commit this page was built from.
Mobrob: common questions
What microcontroller does the Mobrob use?
The Mobrob is built around the ESP32_1, from the ESP32 family.
How big is the Mobrob PCB?
The Mobrob measures 100 × 54 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Mobrob?
27 components, from 17 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Mobrob design files?
From the Spacha/mobrob repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Mobrob design in my own project?
The repository has no license, so all rights stay with Spacha. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Mobrob without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k