TitanLegs
SRA-VJTI·TitanLegs·PCB_Design/bldc_pcb_design/bldc_pcb_design.kicad_pcb
About the TitanLegs PCB
TitanLegs is an open source ESP32 PCB design by SRA-VJTI, published on GitHub under the MIT license. It is a 4-layer board measuring 55.5 × 55.5 mm, with 69 components from 37 distinct parts.
Its main chip is the ESP32-WROOM-32D, from the ESP32 family. Other key parts include the DRV8305NPHPR, AS5600-ASOT, LM2672M-3.3, CSD18532NQ5BT and DS18S20Z+. By type, the board carries 30 capacitors, 17 resistors, 11 ICs, 5 diodes, 2 switches and 2 transformers.
It belongs with the robotics & motion designs in this gallery.
Main components on the TitanLegs
TitanLegs bill of materials (BOM)
69 components, 37 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | DRV8305NPHPR | DRV8305NEPHPRQ1_with_GND_pads | IC1 |
| 1 | ESP32-WROOM-32D | ESP32-WROOM-32 | U1 |
| 1 | AS5600-ASOT | AS5600 | U2 |
| 1 | LM2672M-3.3 | SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 6 | CSD18532NQ5BT | CSD18532NQ5B | U4, U5, U6, U7, U8, U9 |
| 1 | DS18S20Z+ | DS18S20Z_ | U10 |
| 1 | Conn_01x06_Female | PinHeader_1x06_P2.54mm_Vertical | J1 |
| 1 | BOOT | Tactile_Switch | SW1 |
| 1 | RESET | Tactile_Switch | SW2 |
| 2 | BC847 | BC847 | T1, T2 |
| 1 | 3A 40V | D_0603_1608Metric | D1 |
| 4 | LED | D_0603_1608Metric | D2, D3, D4, D5 |
| 1 | 47uH | 8D43 | L1 |
| 1 | 100 nF | C_0603_1608Metric | C1 |
| 1 | 68uF 10V | CP_Elec_6.3x7.7 | C2 |
| 1 | 50V 0.01uF | C_0603_1608Metric | C3 |
| 1 | 10 uF 50V | C_0603_1608Metric | C4 |
| 1 | 0.1 uF 50V | C_0603_1608Metric | C5 |
| 1 | 100uF 50V | CP_Elec_6.3x7.7 | C6 |
| 1 | 1uF 50V | C_0603_1608Metric | C7 |
Show 17 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | 1nF | C_0603_1608Metric | C8, C12, C14 |
| 2 | 330uF 50V | CP_Elec_10x10 | C9, C13 |
| 3 | 1uF | C_0603_1608Metric | C10, C16, C19 |
| 3 | 0.01uF | C_0603_1608Metric | C11, C17, C20 |
| 2 | 10uF 50V | C_0603_1608Metric | C15, C18 |
| 1 | 4.7uF | C_0603_1608Metric | C21 |
| 3 | 1uF 6.3V | C_0603_1608Metric | C22, C24, C30 |
| 1 | 2.2uF 16V | C_0603_1608Metric | C23 |
| 1 | 1uF 16V | C_0603_1608Metric | C25 |
| 2 | 0.1uF | C_0603_1608Metric | C26, C28 |
| 2 | 0.047uF | C_0603_1608Metric | C27, C29 |
| 6 | 10k | R_0603_1608Metric | R1, R4, R11, R14, R16, R17 |
| 3 | 4.7k | R_0603_1608Metric | R2, R3, R9 |
| 3 | 330 | R_0603_1608Metric | R5, R12, R15 |
| 3 | 5m | Shunt_Resistor_L7.0mm_B4.0mm_H1.0mm | R6, R7, R8 |
| 1 | 5k | R_0603_1608Metric | R10 |
| 1 | 100 | R_0603_1608Metric | R13 |
TitanLegs design files
The KiCad project lives in the SRA-VJTI/TitanLegs repository on GitHub; these links point at the commit this page was built from.
TitanLegs: common questions
What microcontroller does the TitanLegs use?
The TitanLegs is built around the ESP32-WROOM-32D, from the ESP32 family.
How big is the TitanLegs PCB?
The TitanLegs measures 55.5 × 55.5 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the TitanLegs?
69 components, from 37 distinct parts. The full bill of materials is listed on this page.
Where can I download the TitanLegs design files?
From the SRA-VJTI/TitanLegs repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the TitanLegs design in my own project?
Yes, under the terms of its MIT license, which SRA-VJTI chose for the repository.
Can I test firmware for the TitanLegs without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k