Joseppe-Pocket-Pet-
srisine·Joseppe-Pocket-Pet-·PCB/pcb.kicad_pcb
About the Joseppe-Pocket-Pet- PCB
Joseppe-Pocket-Pet- is an open source ESP32 PCB design by srisine, published on GitHub. It is a 2-layer board measuring 96.5 × 46 mm, with 6 components from 4 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. By type, the board carries 3 switches, 1 IC, 1 connector and 1 buzzer.
It belongs with the iot & wireless, power & battery and displays & leds designs in this gallery.
From the project
Pocket pet of my own!
Main components on the Joseppe-Pocket-Pet-
Joseppe-Pocket-Pet- bill of materials (BOM)
6 components, 4 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C3-DIP | U1 |
| 1 | Conn_01x08_Pin | PinSocket_1x08_P2.54mm_Vertical | J1 |
| 1 | Buzzer | Buzzer_12x9.5RM7.6 | BZ1 |
| 3 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1, SW2, SW3 |
Joseppe-Pocket-Pet- design files
The KiCad project lives in the srisine/Joseppe-Pocket-Pet- repository on GitHub; these links point at the commit this page was built from.
- LayoutPCB/pcb.kicad_pcb
- SchematicPCB/pcb.kicad_sch
Joseppe-Pocket-Pet-: common questions
What microcontroller does the Joseppe-Pocket-Pet- use?
The Joseppe-Pocket-Pet- is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the Joseppe-Pocket-Pet- PCB?
The Joseppe-Pocket-Pet- measures 96.5 × 46 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Joseppe-Pocket-Pet-?
6 components, from 4 distinct parts. The full bill of materials is listed on this page.
Where can I download the Joseppe-Pocket-Pet- design files?
From the srisine/Joseppe-Pocket-Pet- repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Joseppe-Pocket-Pet- design in my own project?
The repository has no license, so all rights stay with srisine. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Joseppe-Pocket-Pet- without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k