MCU-Datalogger
stephen-j8·MCU-Datalogger-KICAD
About the MCU-Datalogger PCB
MCU-Datalogger is an open source AVR/Arduino PCB design by stephen-j8, published on GitHub under the MIT license. It is a 4-layer board measuring 45.2 × 30.8 mm, with 22 components from 14 distinct parts.
Its main chip is the ATMEGA328P-AU, from the AVR/Arduino family. Other key parts include the 24LC1025 and DS1337S_. By type, the board carries 7 resistors, 5 capacitors, 4 ICs, 2 crystals, 2 diodes and 1 battery holder.
It belongs with the power & battery and dev boards & breakouts designs in this gallery.
From the project
MCU Datalogger — ATmega328P-based data logging PCB with DS1307 real-time clock, dual I²C EEPROM storage (24LC025 + 24LC1025), battery backup, UART/SPI/I²C breakout headers, and ICSP programming port. Designed in KiCad 10 on a 4-layer stackup. Includes full schematic, PCB layout, and Gerber files.
Main components on the MCU-Datalogger
MCU-Datalogger bill of materials (BOM)
22 components, 14 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 24LC1025 | SOIC-8_5.3x5.3mm_P1.27mm | U1, U2 |
| 1 | ATMEGA328P-AU | QFP80P900X900X120-32N | U3 |
| 1 | DS1337S_ | SOIC127P600X175-8N | U4 |
| 1 | 32.768 KHz | Crystal_SMD_5032-2Pin_5.0x3.2mm_HandSoldering | Y1 |
| 1 | 16 MHz | Crystal_SMD_5032-2Pin_5.0x3.2mm_HandSoldering | Y2 |
| 1 | Battery | PinHeader_1x02_P2.54mm_Vertical | BT1 |
| 1 | Conn_01x04_Pin | PinHeader_1x04_P2.00mm_Vertical | I2C |
| 2 | LED | LED_0805_2012Metric | D1, D2 |
| 2 | 0.1uF | C_0805_2012Metric | C1, C4 |
| 2 | 22pF | C_0805_2012Metric | C2, C3 |
| 1 | 100nF | C_0805_2012Metric | C5 |
| 3 | 10K | R_0805_2012Metric | R1, R2, R6 |
| 2 | 4.7K | R_0805_2012Metric | R3, R4 |
| 2 | 330 | R_0805_2012Metric | R5, R7 |
MCU-Datalogger design files
The KiCad project lives in the stephen-j8/MCU-Datalogger-KICAD repository on GitHub; these links point at the commit this page was built from.
- LayoutMCU Datalogger.kicad_pcb
- SchematicMCU Datalogger.kicad_sch
MCU-Datalogger: common questions
What microcontroller does the MCU-Datalogger use?
The MCU-Datalogger is built around the ATMEGA328P-AU, from the AVR/Arduino family.
How big is the MCU-Datalogger PCB?
The MCU-Datalogger measures 45.2 × 30.8 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the MCU-Datalogger?
22 components, from 14 distinct parts. The full bill of materials is listed on this page.
Where can I download the MCU-Datalogger design files?
From the stephen-j8/MCU-Datalogger-KICAD repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the MCU-Datalogger design in my own project?
Yes, under the terms of its MIT license, which stephen-j8 chose for the repository.
Can I test firmware for the MCU-Datalogger without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k