Amiga-1000-keyboard project

steveed·amiga-1000-keyboard-project·pcb/rev_2/amiga-1000-keyboard-rev2.kicad_pcb

Amiga-1000-keyboard project PCB layout, top view — open source AVR/Arduino board by steveed

About the Amiga-1000-keyboard project PCB

Amiga-1000-keyboard project is an open source AVR/Arduino PCB design by steveed, published on GitHub under the CC-BY-NC-4.0 license. It is a 2-layer board measuring 389.3 × 145 mm, with 127 components from 20 distinct parts.

Its main chip is the ATmega32U4-AU, from the AVR/Arduino family. Other key parts include the TPS2116DRLR and USBLC6-2SC6. By type, the board carries 91 diodes, 15 capacitors, 10 resistors, 3 ICs, 3 connectors and 3 inductors.

It belongs with the keyboards and retro computing designs in this gallery, and the repository also holds 1 earlier revision of it.

From the project

Recreation of the original Amiga 1000 PCB

A surface-mount version of the board that the fab can assemble from stocked parts, for Cherry MX switches; only the keyswitches and the Caps Lock LED (which sits inside its switch) are fitted by hand. Rev 1, the through-hole recreation of the original that takes the original 6500/1 controller, stays in pcb/.

The outline, mounting holes and switch positions match rev 1, so the case fits both boards; rev 2 needs its own MX plate.

Main components on the Amiga-1000-keyboard project

Amiga-1000-keyboard project bill of materials (BOM)

127 components, 20 distinct parts.

QtyPartRefs
1
ATmega32U4-AU
U1
1
TPS2116DRLR
U2
1
USBLC6-2SC6
U3
1
16MHz
Y1
1
AMIGA
J1
1
USB-C
J2
1
ISP
J3
1
500mA
F1
91
1N4148W
D1, D2, D3, D4, D5, D6, D7, D8 +83
3
FB
FB1, FB2, FB3
2
12pF
C1, C2
5
100nF
C3, C4, C5, C6, C9
2
10uF
C7, C12
3
1uF
C8, C10, C11
3
1nF
C13, C14, C15
4
10k
R1, R2, R5, R6
1
330
R3
1
33k
R4
2
5.1k
R7, R8
2
22
R9, R10

Amiga-1000-keyboard project design files

The KiCad project lives in the steveed/amiga-1000-keyboard-project repository on GitHub; these links point at the commit this page was built from.

Amiga-1000-keyboard project: common questions

What microcontroller does the Amiga-1000-keyboard project use?

The Amiga-1000-keyboard project is built around the ATmega32U4-AU, from the AVR/Arduino family.

How big is the Amiga-1000-keyboard project PCB?

The Amiga-1000-keyboard project measures 389.3 × 145 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Amiga-1000-keyboard project?

127 components, from 20 distinct parts. The full bill of materials is listed on this page.

Where can I download the Amiga-1000-keyboard project design files?

From the steveed/amiga-1000-keyboard-project repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Amiga-1000-keyboard project design in my own project?

It is published under CC-BY-NC-4.0, which limits how it may be reused; read the license before building on it.

Can I test firmware for the Amiga-1000-keyboard project without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

Earlier revisions in the repo: amiga-1000-keyboard

Similar boards