UniBikes
strifel·UniBikes
About the UniBikes PCB
UniBikes is an open source ESP32 PCB design by strifel, published on GitHub. It is a 2-layer board measuring 100 × 100 mm, with 29 components from 13 distinct parts.
Its main chip is the ESP32-C3, from the ESP32 family. Other key parts include the TLV1117-33. By type, the board carries 10 diodes, 6 resistors, 4 connectors, 4 capacitors, 3 switches and 2 ICs.
From the project
An PCB showing bike sharing stations at TU Dortmund University.
Unibikes shows the 10 bike sharing locations at TU Dortmund University in germany with an RGB LED each. Each LED can therefore represent if there are none, some or a few bikes at that station.

Main components on the UniBikes
UniBikes bill of materials (BOM)
29 components, 13 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3 | ESP32-C3-WROOM-02 | U1 |
| 1 | TLV1117-33 | SOT-223-3_TabPin2 | U2 |
| 1 | USB_C_Receptacle_USB2.0 | USB_C_Receptacle_GCT_USB4110 | J0 |
| 2 | Conn_01x04_Pin | PinSocket_1x04_P2.54mm_Vertical_SMD_Pin1Left | J1, J2 |
| 1 | Conn_01x02_Pin | PinSocket_1x02_P2.54mm_Vertical_SMD_Pin1Left | J3 |
| 3 | SW_Push | SW_Push_SPST_NO_Alps_SKRK | SW1, SW2, SW3 |
| 10 | WS2812B | LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D1, D2, D3, D4, D5, D6, D7, D8 +2 |
| 2 | 10 uF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C4 |
| 1 | 1 uF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2 |
| 1 | 100nF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3 |
| 1 | 1k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1 |
| 3 | 10k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2, R3, R4 |
| 2 | 5.1k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R5, R6 |
UniBikes design files
The KiCad project lives in the strifel/UniBikes repository on GitHub; these links point at the commit this page was built from.
- LayoutUniBikes.kicad_pcb
- SchematicUniBikes.kicad_sch
UniBikes: common questions
What microcontroller does the UniBikes use?
The UniBikes is built around the ESP32-C3, from the ESP32 family.
How big is the UniBikes PCB?
The UniBikes measures 100 × 100 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the UniBikes?
29 components, from 13 distinct parts. The full bill of materials is listed on this page.
Where can I download the UniBikes design files?
From the strifel/UniBikes repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the UniBikes design in my own project?
The repository has no license, so all rights stay with strifel. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the UniBikes without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k