Rover-PCB-

Sujay-1010·Rover-PCB--KiCAD·atmega328p/atmega328p.kicad_pcb

Rover-PCB- layout, top view — open source AVR/Arduino board by Sujay-1010

About the Rover-PCB-

Rover-PCB- is an open source AVR/Arduino PCB design by Sujay-1010, published on GitHub. It is a 2-layer board measuring 42.2 × 82 mm, with 39 components from 19 distinct parts.

Its main chip is the ATMEGA328-A, from the AVR/Arduino family. Other key parts include the L293D, MPU-6050, LM2576HVS-5, TMF8820 and AMS1117-3.3. By type, the board carries 14 resistors, 8 ICs, 8 capacitors, 4 modules, 2 switches and 1 diode.

From the project

Following pcb contains a rover pcb design, its schematics, its bom(bill of materials), and the working paramters of all the components used.

Main components on the Rover-PCB-

Rover-PCB- bill of materials (BOM)

39 components, 19 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ATMEGA328-A
ATmega328-A
U1
2
L293D
U2, U9
1
~
U4
1
MPU-6050
U5
1
LM2576HVS-5
U6
1
TMF8820
U7
1
AMS1117-3.3
U8
4
Motor_DC
M1, M2, M3, M4
2
SW_SPST
SW7, SW8
1
CONN_01X03_PIN
Conn_01x03_Pin
Servo1
1
SS34
D1
1
100MU
100mu
L1
1
0.01U
0.01u
C1
1
100U
100u
C2
1
220U
220u
C3
3
0.1U
0.1u
C4, C5, C8
2
10U
10u
C6, C7
12
10K
10k
R1, R2, R3, R4, R5, R6, R7, R8 +4
2
4.7K
4.7k
R13, R14

Rover-PCB- design files

The KiCad project lives in the Sujay-1010/Rover-PCB--KiCAD repository on GitHub; these links point at the commit this page was built from.

Rover-PCB-: common questions

What microcontroller does the Rover-PCB- use?

The Rover-PCB- is built around the ATMEGA328-A, from the AVR/Arduino family.

How big is the Rover-PCB-?

The Rover-PCB- measures 42.2 × 82 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Rover-PCB-?

39 components, from 19 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Rover-PCB- design files?

From the Sujay-1010/Rover-PCB--KiCAD repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Rover-PCB- design in my own project?

The repository has no license, so all rights stay with Sujay-1010. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Rover-PCB- without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

Similar boards