Foc control

sujaygouda123·foc-control

Foc control PCB layout, top view — open source STM32 board by sujaygouda123

About the Foc control PCB

Foc control is an open source STM32 PCB design by sujaygouda123, published on GitHub. It is a 8-layer board measuring 80 × 80 mm, with 87 components from 44 distinct parts.

Its main chip is the STM32G474RET3, from the STM32 family. Other key parts include the MCP2562FD-E/SN, AS5047P-ATSM, LM5164DDAR, AP2112K-3.3 and DRV8353SRTAR. By type, the board carries 46 capacitors, 22 resistors, 7 ICs, 6 transistors, 2 connectors and 2 inductors.

It belongs with the robotics & motion designs in this gallery.

From the project

BLDC field-oriented-control board for a humanoid robot actuator. KiCad 10, Ø80 mm, 8 layers, 1.6 mm.

BLDC field-oriented-control board for a humanoid robot actuator. KiCad 10, Ø80 mm, 8 layers, 1.6 mm.

- One cable per link: VBUS + GND (16 AWG) and CAN-H / CAN-L as a twisted pair. - Two XT30 2+2 connectors per board (IN, OUT), 15 A continuous. - 120 Ω termination only at the two ends of each bus (JP1 on the last actuator).

Inner layers are 1 oz. Power runs on the 2 oz outer layers; every signal layer sits next to a plane.

Foc control, from the project README
From the project README

Main components on the Foc control

Foc control bill of materials (BOM)

87 components, 44 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
MCP2562FD-E/SN
U1
1
AS5047P-ATSM
U2
1
STM32G474RET3
U3
2
LM5164DDAR
U4, U5
1
AP2112K-3.3
U6
1
DRV8353SRTAR
U7
6
BSC040N10NS5ATMA1
Q1, Q2, Q3, Q4, Q5, Q6
1
ABM3B-8.000MHZ-B2-T
Y1
1
XT30PW(2+2)-M.G.B
BUS_IN
J1
1
XT30PW(2+2)-M.G.B
BUS_OUT
J2
1
NCP18XH103F03RB
NTC 10k
TH1
2
SRN6045TA-680M
68 µH
L1, L2
13
100 nF 16V X7R
C1, C2, C3, C4, C6, C7, C8, C9 +5
7
1 µF 16V X7R
C5, C13, C31, C32, C35, C38, C39
1
10 µF 16V X5R
C11
2
27 pF 50V C0G
C14, C15
7
2.2 µF 100V X7R
C17, C18, C24, C25, C41, C42, C43
2
2.2 nF 50V X7R
C19, C26
2
3.3 nF 50V X7R
C20, C27
1
56 pF 50V C0G
C21
Show 24 more
QtyPartRefs
2
22 µF 25V X7R
C22, C23
2
22 µF 16V X7R
C28, C30
1
180 pF 50V C0G
C29
1
100 nF 25V X7R
C33
1
10 µF 25V X7R
C34
1
47 nF 100V X7R
C36
2
UUX2A470MNL1GS
47 µF 100V
C44, C45
1
10 nF 16V X7R
C46
1
120 Ω 1%
R1
4
10 kΩ
R2, R3, R14, R15
1
100k 1%
R4
1
453 kΩ 1%
R5
2
49.9 kΩ 1%
R6, R11
1
453k 1%
R7
1
41.2k 1%
R8
1
200k 1%
R9
1
158k 1%
R10
1
1M 1%
R12
1
82k 1%
R13
1
100K
100k
R16
3
1mΩ 1W WSL25121L000FEA
R17, R18, R19
1
100k 1%
R20
1
3.3k 1%
R21
1
10k 1%
R22

Foc control design files

The KiCad project lives in the sujaygouda123/foc-control repository on GitHub; these links point at the commit this page was built from.

Foc control: common questions

What microcontroller does the Foc control use?

The Foc control is built around the STM32G474RET3, from the STM32 family.

How big is the Foc control PCB?

The Foc control measures 80 × 80 mm, has 8 copper layers and is 1.6 mm thick.

How many components are on the Foc control?

87 components, from 44 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Foc control design files?

From the sujaygouda123/foc-control repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Foc control design in my own project?

The repository has no license, so all rights stay with sujaygouda123. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Foc control without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards