Eprinter
tact1m4n3·eprinter·pcb/eprinter.kicad_pcb
About the Eprinter PCB
Eprinter is an open source ESP32 PCB design by tact1m4n3, published on GitHub under the MIT license. It is a 4-layer board measuring 28 × 70 mm, with 57 components from 30 distinct parts.
Its main chip is the ESP32-C3-WROOM-02, from the ESP32 family. Other key parts include the TPS63802DLAR, LM66100DCK and ATL431BIDBZR. By type, the board carries 23 resistors, 16 capacitors, 6 diodes, 4 ICs, 2 transistors and 2 connectors.
Main components on the Eprinter
Eprinter bill of materials (BOM)
57 components, 30 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3-WROOM-02 | ESP32-C3-WROOM-02 | U1 |
| 1 | TPS63802DLAR | VSON-10_L3.0-W2.0-P0.50-TL | U2 |
| 1 | LM66100DCK | SOT-363_SC-70-6 | U3 |
| 1 | ATL431BIDBZR | SOT-23-3 | U6 |
| 1 | Si2301 | SOT-23 | Q1 |
| 1 | BSS138 | SOT-23 | Q2 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB-C_SMD-TYPE-C-31-M-12_1 | J1 |
| 1 | AFC07-S24FCC-00 | FPC-SMD_AFC07-S24FCC-00 | J2 |
| 2 | SW_PUSH | SW-SMD_L3.9-W3.0-P4.45 | SW1, SW2 |
| 1 | BAT54J | D_SOD-323F | D1 |
| 1 | LED | LED_0603_1608Metric | D2 |
| 1 | PMEG2010EJ | D_SOD-323F | D3 |
| 3 | MBR0530 | D_SOD-123 | D4, D5, D6 |
| 1 | 68uH/500mA | IND-SMD_L4.0-W4.0 | L1 |
| 1 | 0.47u | L_1210_3225Metric | L2 |
| 4 | 10u | C_0805_2012Metric | C2, C5, C7, C16 |
| 8 | 1u | C_0603_1608Metric | C3, C8, C9, C11, C12, C13, C14, C15 |
| 3 | 100n | C_0603_1608Metric | C4, C6, C17 |
| 1 | 22u | C_0805_2012Metric | C10 |
| 2 | 22 | R_0603_1608Metric | R1, R2 |
Show 10 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | 10k | R_0603_1608Metric | R3, R6, R8, R12 |
| 2 | 5.1k | R_0603_1608Metric | R4, R7 |
| 1 | 470 | R_0603_1608Metric | R5 |
| 1 | 0.1 | R_0603_1608Metric | R9 |
| 4 | 4.7M | R_0603_1608Metric | R10, R14, R18, R23 |
| 3 | 1M | R_0603_1608Metric | R11, R15, R16 |
| 1 | 0.47 | R_0603_1608Metric | R13 |
| 1 | 680k | R_0603_1608Metric | R17 |
| 3 | 510k | R_0603_1608Metric | R19, R20, R21 |
| 1 | 91k | R_0603_1608Metric | R22 |
Eprinter design files
The KiCad project lives in the tact1m4n3/eprinter repository on GitHub; these links point at the commit this page was built from.
- Layoutpcb/eprinter.kicad_pcb
- Schematicpcb/eprinter.kicad_sch
Eprinter: common questions
What microcontroller does the Eprinter use?
The Eprinter is built around the ESP32-C3-WROOM-02, from the ESP32 family.
How big is the Eprinter PCB?
The Eprinter measures 28 × 70 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Eprinter?
57 components, from 30 distinct parts. The full bill of materials is listed on this page.
Where can I download the Eprinter design files?
From the tact1m4n3/eprinter repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Eprinter design in my own project?
Yes, under the terms of its MIT license, which tact1m4n3 chose for the repository.
Can I test firmware for the Eprinter without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k