Kitsujikan
techmoocher·kitsujikan·PCB/kitsujikan.kicad_pcb
About the Kitsujikan PCB
Kitsujikan is an open source ESP32 PCB design by techmoocher, published on GitHub under the MIT license. It is a 2-layer board measuring 65 × 90 mm, with 19 components from 17 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. By type, the board carries 6 switches, 5 resistors, 3 connectors, 1 IC, 1 transistor and 1 buzzer.
It belongs with the displays & leds and power & battery designs in this gallery.
From the project
A little Pomodoro timer (my first hardware project!!!)
A rechargeable, pocket-sized Pomodoro timer with an OLED display and colour-coded buttons, designed for Hack Club's Half-Life 10-week hardware challenge.
- One-press focus sessions: 30, 60 or 90 minutes, one button each. - Automatic breaks: when a session ends, the buzzer sounds and the timer offers a 5-minute break. Press green to accept or red to skip. After the break, it offers to repeat the last session length. - Clear display: a 0.96" OLED shows the time left as HH:MM:SS. Hours are hidden when zero, and minutes and seconds always show two digits. - Pause: press red during a session. -…

Main components on the Kitsujikan
Kitsujikan bill of materials (BOM)
19 components, 17 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C6-DIP | U1 |
| 1 | 2N3904 | TO-92_Inline | Q1 |
| 1 | Battery | JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J1 |
| 1 | XIAO_BAT | SolderWire-0.15sqmm_1x02_P4mm_D0.5mm_OD1.5mm | J2 |
| 1 | OLED_SSD1306 | Display_128x64_096_I2C | J3 |
| 1 | Buzzer_passive | Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | Power | SW_Slide_SPDT_Straight_CK_OS102011MS2Q | SW1 |
| 1 | 30min | SW_PUSH-12mm | SW2 |
| 1 | 60min | SW_PUSH-12mm | SW3 |
| 1 | 90min | SW_PUSH-12mm | SW4 |
| 1 | OK_GREEN | SW_PUSH-12mm | SW5 |
| 1 | NO_RED | SW_PUSH-12mm | SW6 |
| 1 | 1N4148 | D_DO-35_SOD27_P7.62mm_Horizontal | D1 |
| 1 | 100nF | C_Disc_D5.0mm_W2.5mm_P5.00mm | C1 |
| 2 | 200k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2 |
| 2 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R3, R5 |
| 1 | 1k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R4 |
Kitsujikan design files
The KiCad project lives in the techmoocher/kitsujikan repository on GitHub; these links point at the commit this page was built from.
- LayoutPCB/kitsujikan.kicad_pcb
- SchematicPCB/kitsujikan.kicad_sch
- BOMkitsujikan_BOM.csv
Kitsujikan: common questions
What microcontroller does the Kitsujikan use?
The Kitsujikan is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the Kitsujikan PCB?
The Kitsujikan measures 65 × 90 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Kitsujikan?
19 components, from 17 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Kitsujikan design files?
From the techmoocher/kitsujikan repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Kitsujikan design in my own project?
Yes, under the terms of its MIT license, which techmoocher chose for the repository.
Can I test firmware for the Kitsujikan without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k