Test 22
TekBot-Robotics-Challenge·2025-Team-The_Winners-Docs·electonic/test2/kicad/station_control/Test_22.kicad_pcb
About the Test 22 PCB
Test 22 is an open source AVR/Arduino PCB design by TekBot-Robotics-Challenge, published on GitHub. It is a 2-layer board measuring 72 × 58.7 mm, with 27 components from 14 distinct parts.
Its main chip is the ATmega328-P, from the AVR/Arduino family. By type, the board carries 8 resistors, 7 diodes, 4 connectors, 4 capacitors, 1 IC and 1 transistor.
Main components on the Test 22
Test 22 bill of materials (BOM)
27 components, 14 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATmega328-P | DIP-28_W7.62mm | U1 |
| 1 | NMOS | TO-220F-3_Vertical | Q1 |
| 1 | Crystal | Crystal_HC49-U_Vertical | Y1 |
| 1 | Prog_connector | PinSocket_1x06_P2.54mm_Horizontal | J1 |
| 1 | LCD_connector | PinSocket_1x08_P2.54mm_Vertical | J2 |
| 1 | I2C_connector | JST_EH_S4B-EH_1x04_P2.50mm_Horizontal | J3 |
| 1 | Jack-DC | BarrelJack_Horizontal | J4 |
| 1 | SW_Push | SW_PUSH_6mm | SW1 |
| 7 | LED | LED_D3.0mm | D1, D2, D3, D4, D5, D6, D7 |
| 2 | 22pF | C_Disc_D7.5mm_W5.0mm_P7.50mm | C1, C2 |
| 1 | 100n | C_Disc_D7.5mm_W5.0mm_P7.50mm | C3 |
| 1 | 100nF | C_Disc_D7.5mm_W5.0mm_P7.50mm | C4 |
| 7 | 220 | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R3, R4, R5, R6, R7, R8 |
| 1 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2 |
Test 22 design files
The KiCad project lives in the TekBot-Robotics-Challenge/2025-Team-The_Winners-Docs repository on GitHub; these links point at the commit this page was built from.
Test 22: common questions
What microcontroller does the Test 22 use?
The Test 22 is built around the ATmega328-P, from the AVR/Arduino family.
How big is the Test 22 PCB?
The Test 22 measures 72 × 58.7 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Test 22?
27 components, from 14 distinct parts. The full bill of materials is listed on this page.
Where can I download the Test 22 design files?
From the TekBot-Robotics-Challenge/2025-Team-The_Winners-Docs repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Test 22 design in my own project?
The repository has no license, so all rights stay with TekBot-Robotics-Challenge. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Test 22 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in 2025-Team-The_Winners-Docs
AVR/Arduino
Test 3
TekBot-Robotics-Challenge
105.7 × 75.5 mm71 parts2LNo license0ESP8266
Test convoyeur
TekBot-Robotics-Challenge
82.6 × 82.3 mm47 parts2LNo license0Circuit imprimé de l'alimentation 5V/2A
TekBot-Robotics-Challenge
111.2 × 39.2 mm16 parts2LNo license0AVR/Arduino
Test 2
TekBot-Robotics-Challenge
51.2 × 54.2 mm13 parts2LNo license04Batteries Charger
TekBot-Robotics-Challenge
119.2 × 101.9 mm9 parts2LNo license0
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k