Half life week-1

theonlydesigner·half-life-week-1·KiCAD/half-life.kicad_pcb

Half life week-1 PCB layout, top view — open source RP2040/RP2350 board by theonlydesigner

About the Half life week-1 PCB

Half life week-1 is an open source RP2040/RP2350 PCB design by theonlydesigner, published on GitHub. It is a 2-layer board measuring 21 × 51 mm, with 33 components from 16 distinct parts.

Its main chip is the RP2040, from the RP2040/RP2350 family. Other key parts include the MCP1700x-330xxTT and W25Q128JVS. By type, the board carries 17 capacitors, 7 resistors, 4 connectors, 3 ICs, 1 crystal and 1 switch.

It belongs with the dev boards & breakouts designs in this gallery.

From the project

at the center of the madness is the RP2040 microcontroller chip which handles all the processing. it is paired with a W25Q128 QSPI flash memory chip for storing firmware and a 12MHz crystal oscillator to provide the clock signal. power is delivered via a USB-C connector featuring

at the center of the madness is the RP2040 microcontroller chip which handles all the processing. it is paired with a W25Q128 QSPI flash memory chip for storing firmware and a 12MHz crystal oscillator to provide the clock signal. power is delivered via a USB-C connector featuring 5.1k pull-down resistors so modern power supplies actually negotiate power correctly. an MCP1700 LDO voltage regulator takes that input and steps it down to a stable 3.3V for the system. finally every single GPIO pin is broken out onto dual headers so the board can easily interface with a mini hackpad.

Half life week-1, from the project README
From the project README

Main components on the Half life week-1

Half life week-1 bill of materials (BOM)

33 components, 16 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
RP2040
U1
1
MCP1700x-330xxTT
U2
1
W25Q128JVS
U4
1
12MHz
Y1
1
USB_C_Receptacle_USB2.0_14P
J1
2
Conn_01x20
J2, J3
1
Conn_01x03
J4
1
SW_Push
SW1
2
1uF
C1, C10
11
0.1uF
C2, C3, C4, C5, C6, C7, C8, C9 +3
2
10uF
C13, C14
2
33pF
C15, C16
2
5.1K
R1, R2
2
27
R3, R4
2
1K
R5, R6
1
10K
R7

Half life week-1 design files

The KiCad project lives in the theonlydesigner/half-life-week-1 repository on GitHub; these links point at the commit this page was built from.

Half life week-1: common questions

What microcontroller does the Half life week-1 use?

The Half life week-1 is built around the RP2040, from the RP2040/RP2350 family.

How big is the Half life week-1 PCB?

The Half life week-1 measures 21 × 51 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Half life week-1?

33 components, from 16 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Half life week-1 design files?

From the theonlydesigner/half-life-week-1 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Half life week-1 design in my own project?

The repository has no license, so all rights stay with theonlydesigner. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Half life week-1 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

Similar boards