Pcb a rev3
TheStaticTurtle·catears·electronics/pcb_a_rev3/pcb_a_rev3.kicad_pcb
About the Pcb a rev3
Pcb a rev3 is an open source ESP32 PCB design by TheStaticTurtle, published on GitHub under the MIT license. It is a 4-layer board measuring 48.1 × 51.4 mm, with 316 components from 18 distinct parts.
Its main chip is the ESP32-S3, from the ESP32 family. Other key parts include the W25Q128JVP and MPM3805. By type, the board carries 290 diodes, 14 capacitors, 5 resistors, 3 ICs, 1 crystal and 1 antenna.
It belongs with the displays & leds, power & battery and iot & wireless designs in this gallery, and the repository also holds 1 earlier revision of it.
From the project
High-tech, RGB LED-matrix cat ears, built for fun.
High-tech, RGB LED-matrix cat ears, built for fun.
Each ear and each side of the headband carries a small 2D matrix of tiny XL-1010 WS2812B LEDs, driven by an ESP32-S3 running WLED with sound-reactive animations, all powered over a single USB-C cable.
- cad/: 3D models of the headband and ears - electronics/: KiCad projects for each PCB revision - wled/: WLED config, presets and the 2D LED map (generated from the KiCad netlist by genledmap.py`)

Main components on the Pcb a rev3
Pcb a rev3 bill of materials (BOM)
316 components, 18 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | W25Q128JVP | WSON-8-1EP_6x5mm_P1.27mm_EP3.4x4.3mm | U1 |
| 1 | MPM3805 | MPM3805 | U2 |
| 1 | ESP32-S3 | QFN-56-1EP_7x7mm_P0.4mm_EP4x4mm | U4 |
| 1 | Crystal_GND24 | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | Antenna_Chip | IRD-C013 | AE1 |
| 1 | ICS-43434 | InvenSense_ICS-43434-6_3.5x2.65mm | MK1 |
| 290 | XL-1010 | XL-1010RGBC | D1, D2, D3, D4, D5, D6, D7, D8 +282 |
| 1 | 2n | L_0402_1005Metric_Pad0.77x0.64mm_HandSolder | L2 |
| 5 | 10u | C_0603_1608Metric | C1, C2, C3, C4, C5 |
| 1 | 1.2p | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C10 |
| 1 | 1.8p | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C11 |
| 2 | TBD | C_0603_1608Metric | C13, C14 |
| 2 | 0.1uF | C_0603_1608Metric | C15, C17 |
| 2 | 1uF | C_0603_1608Metric | C16, C18 |
| 1 | 1nF | C_0603_1608Metric | C19 |
| 2 | 10k | R_0603_1608Metric | R1, R3 |
| 1 | 5.1k | R_0603_1608Metric | R2 |
| 2 | 10k | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R12, R15 |
Pcb a rev3 design files
The KiCad project lives in the TheStaticTurtle/catears repository on GitHub; these links point at the commit this page was built from.
Pcb a rev3: common questions
What microcontroller does the Pcb a rev3 use?
The Pcb a rev3 is built around the ESP32-S3, from the ESP32 family.
How big is the Pcb a rev3?
The Pcb a rev3 measures 48.1 × 51.4 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Pcb a rev3?
316 components, from 18 distinct parts. The full bill of materials is listed on this page.
Where can I download the Pcb a rev3 design files?
From the TheStaticTurtle/catears repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Pcb a rev3 design in my own project?
Yes, under the terms of its MIT license, which TheStaticTurtle chose for the repository.
Can I test firmware for the Pcb a rev3 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in catears
Earlier revisions in the repo: pcb_a
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k