TropicalFruitBowl
TheTank87·TropicalFruitBowl·PCB/TropicalFruitBowl.kicad_pcb
About the TropicalFruitBowl PCB
TropicalFruitBowl is an open source ESP32 PCB design by TheTank87, published on GitHub. It is a 2-layer board measuring 115 × 52 mm, with 11 components from 10 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. Other key parts include the DHT11. By type, the board carries 3 connectors, 3 switches, 2 ICs, 1 capacitor and 1 resistor.
It belongs with the keyboards and sensors designs in this gallery.
From the project
A project that involves using OLEDs.
Main components on the TropicalFruitBowl
TropicalFruitBowl bill of materials (BOM)
11 components, 10 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C6-DIP | U1 |
| 1 | DHT11 | Aosong_DHT11_5.5x12.0_P2.54mm | U2 |
| 1 | OLED | Display_128x64_096_I2C | J1 |
| 1 | ENS160+AHT21 module | PinHeader_1x08_P2.54mm_Vertical | J2 |
| 1 | MPU6050 | PinHeader_1x08_P2.54mm_Vertical | J3 |
| 1 | Slider | Potentiometer_Bourns_PTA1543_Single_Slide | RV1 |
| 2 | SW_Push | Kailh Choc Low-Profile Switches | SW1, SW2 |
| 1 | RotaryEncoder_Switch_MP | RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm | SW3 |
| 1 | 0.1uF | C_0603_1608Metric | C1 |
| 1 | 10K | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1 |
TropicalFruitBowl design files
The KiCad project lives in the TheTank87/TropicalFruitBowl repository on GitHub; these links point at the commit this page was built from.
TropicalFruitBowl: common questions
What microcontroller does the TropicalFruitBowl use?
The TropicalFruitBowl is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the TropicalFruitBowl PCB?
The TropicalFruitBowl measures 115 × 52 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the TropicalFruitBowl?
11 components, from 10 distinct parts. The full bill of materials is listed on this page.
Where can I download the TropicalFruitBowl design files?
From the TheTank87/TropicalFruitBowl repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the TropicalFruitBowl design in my own project?
The repository has no license, so all rights stay with TheTank87. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the TropicalFruitBowl without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k