Numpad
tigmit·Split-Numpad·numpad_Schematics/numpad.kicad_pcb
About the Numpad PCB
Numpad is an open source ESP32 PCB design by tigmit, published on GitHub. It is a 2-layer board measuring 74.6 × 113.5 mm, with 45 components from 8 distinct parts.
Its main chip is the ESP32-WROOM-32, from the ESP32 family. By type, the board carries 18 switches, 17 diodes, 6 resistors, 3 capacitors and 1 IC.
Main components on the Numpad
Numpad bill of materials (BOM)
45 components, 8 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-WROOM-32 | ESP32-WROOM-32 tigmit | U3 |
| 17 | ~ | hotswap socket with neopixel | SW1, SW2, SW3, SW4, SW5, SW6, SW7, SW8 +9 |
| 1 | SW_Push | tigmit pushbutton | SW18 |
| 17 | D | Diode_SOD-123 | D1, D2, D3, D4, D5, D6, D7, D8 +9 |
| 1 | 10UF 10uF | CP_EIA-3528-12_Kemet-T | C1 |
| 1 | 0.1UF 0.1uF | CP_EIA-3528-12_Kemet-T | C2 |
| 1 | tbd | CP_EIA-3528-12_Kemet-T | C3 |
| 6 | 10K | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1, R2, R3, R4, R5, R6 |
Numpad design files
The KiCad project lives in the tigmit/Split-Numpad repository on GitHub; these links point at the commit this page was built from.
Numpad: common questions
What microcontroller does the Numpad use?
The Numpad is built around the ESP32-WROOM-32, from the ESP32 family.
How big is the Numpad PCB?
The Numpad measures 74.6 × 113.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Numpad?
45 components, from 8 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Numpad design files?
From the tigmit/Split-Numpad repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Numpad design in my own project?
The repository has no license, so all rights stay with tigmit. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Numpad without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Split-Numpad
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k