Warp esp32-ethernet v2-brick
Tinkerforge·warp-esp32-ethernet-v2-brick·hardware/warp-esp32-ethernet-v2.kicad_pcb
About the Warp esp32-ethernet v2-brick PCB
Warp esp32-ethernet v2-brick is an open source ESP32 PCB design by Tinkerforge, published on GitHub. It is a 4-layer board measuring 116.5 × 57.5 mm, with 211 components from 81 distinct parts.
Its main chip is the ESP32-WROVER-E, from the ESP32 family. Other key parts include the TMP1075NDRLR, RPL-3.0, PCF85263AT, 74AHC244 and TPD4S010DQA. By type, the board carries 62 connectors, 51 resistors, 50 capacitors, 12 ICs, 6 inductors and 4 diodes.
It belongs with the power & battery and iot & wireless designs in this gallery.
From the project
WARP ESP32 Ethernet Brick 2.0 for WARP4 Charger
WARP ESP32 Ethernet Brick 2.0 =============================
This repository contains the hardware design files of the WARP ESP32 Ethernet Brick 2.0, the main controller board of the WARP4 Charger. The firmware is shared between all WARP Chargers and Energy Managers and can be found at https://github.com/Tinkerforge/esp32-firmware.
.. BEGIN WARP REPOSITORIES (managed block, generated from esp32-firmware/repooverview.rst - do not edit by hand, run updaterepo_overview.py instead)
Main components on the Warp esp32-ethernet v2-brick
Warp esp32-ethernet v2-brick bill of materials (BOM)
211 components, 81 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TMP1075NDRLR | SOT563 | U101 |
| 1 | RPL-3.0 | RPL-3.0 | U102 |
| 1 | PCF85263AT | SO-8 | U103 |
| 1 | ESP32-WROVER-E | ESP32-WROVER-E | U104 |
| 3 | 74AHC244 | TSSOP20 | U201, U203, U303 |
| 1 | TPD4S010DQA | TPD4S010DQA | U202 |
| 1 | KSZ8091RNACA | QFN-24-4x4-EP | U301 |
| 1 | SN74LV138APW | TSSOP16 | U302 |
| 1 | AP22811BW5 | SOT25 | U401 |
| 1 | XMC1404 | QFN48-EP2 | U402 |
| 2 | BC817 | SOT23EBC | Q101, Q102 |
| 1 | 32.768kHz | AB26TRQ | X101 |
| 1 | 25Mhz-10pF | CRYSTAL_3225 | X301 |
| 1 | Boot | SolderJumper | J101 |
| 1 | DM3CS | SD-Card-DM3CS | J102 |
| 1 | TJLC_001LA1 | TJLC-001LA1 | J201 |
| 1 | FLASH | pin_array_1x6-P2mm_D1mm | P101 |
| 1 | 3V3 | TSTP_NANO | P102 |
| 1 | GND | TSTP_NANO | P103 |
| 1 | VIN | TSTP_NANO | P104 |
Show 61 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | VRTC | TSTP_NANO | P105 |
| 3 | MOSI | TSTP_NANO_SMD | P106, P306, P308 |
| 3 | GND | TSTP_NANO_SMD | P107, P310, P313 |
| 3 | MISO | TSTP_NANO_SMD | P108, P307, P309 |
| 1 | INT | TSTP_NANO_SMD | P109 |
| 1 | PLC | 6061-2x4 | P110 |
| 1 | Debug | TSTP_STL | P111 |
| 2 | 3V3 | TSTP_NANO_SMD | P112, P312 |
| 3 | CS | TSTP_NANO_SMD | P113, P301, P315 |
| 3 | CLK | TSTP_NANO_SMD | P114, P305, P316 |
| 4 | CON-SENSOR2 | CON-SENSOR2 | P201, P202, P303, P304 |
| 1 | EVSE | 6061-2x4 | P302 |
| 1 | 12V | TSTP_NANO_SMD | P311 |
| 28 | ~ | TSTP_NANO_SMD | P318, P319, P320, P321, P322, P323, P324, P325 +20 |
| 1 | DNP | 4X0402 | CP101 |
| 6 | 220pF | 4X0402 | CP201, CP202, CP205, CP206, CP301, CP302 |
| 2 | ISO DRILL | LSMTSO-M3 | F101, F102 |
| 9 | 82 | 4X0402 | RP101, RP103, RP104, RP201, RP202, RP205, RP206, RP302 +1 |
| 2 | 1k | 4X0402 | RP102, RP301 |
| 2 | B3U-1000P | B3U-1000P | SW101, SW102 |
| 1 | blue | D0603F | D101 |
| 1 | FDLL3595 | MiniMelf | D102 |
| 2 | BAT54AL | SOT23-3 | D103, D104 |
| 5 | FB | R0603F | L101, L103, L301, L302, L401 |
| 1 | FB 35m 4A | R1210 | L102 |
| 14 | 100nF | C0402F | C101, C104, C106, C113, C114, C128, C201, C203 +6 |
| 1 | DSK-3R3H334T-HL | DSK | C102 |
| 4 | 10uF/50V | C1206 | C103, C108, C111, C117 |
| 2 | 100uF | C1210 | C105, C125 |
| 5 | 1uF | C0603F | C107, C121, C122, C123, C126 |
| 5 | 22uF | C1206 | C109, C110, C129, C303, C310 |
| 1 | 1µF | C0603F | C112 |
| 1 | DNP | C0402F | C115 |
| 6 | 2.2uF | C0603F | C116, C119, C301, C302, C311, C401 |
| 1 | 100nF/12V | C0603F | C118 |
| 1 | 39pF | C0603F | C120 |
| 4 | 100nF | C0603F | C127, C130, C402, C403 |
| 1 | 220nF | C0603F | C131 |
| 2 | 22pF | C0402F | C306, C308 |
| 1 | 100nF/50V | C0402F | C312 |
| 1 | DNP | C1206 | C314 |
| 8 | 10k | R0402F | R1, R2, R111, R201, R202, R301, R318, R319 |
| 1 | 68 | R0402F | R101 |
| 1 | 20k | R0402F | R102 |
| 3 | 1k | R0402F | R103, R114, R115 |
| 1 | 100k | R0603F | R104 |
| 2 | 47k | R0603F | R105, R117 |
| 1 | 1k | R0603F | R106 |
| 1 | 100 | R0402F | R107 |
| 2 | 100k | R0402F | R108, R109 |
| 3 | 470 | R0402F | R110, R315, R316 |
| 1 | DNP (10k) | R0402F | R112 |
| 5 | 0 | R0402F | R113, R311, R312, R313, R314 |
| 2 | 15k | R0603F | R116, R118 |
| 3 | 82 | R0402F | R119, R406, R407 |
| 1 | DNP | R0402F | R120 |
| 1 | DNP | 1812 | R203 |
| 3 | 4.7k | R0402F | R204, R309, R310 |
| 1 | 6.49k | R0402F | R302 |
| 6 | 10 | R0402F | R303, R304, R305, R306, R307, R308 |
| 5 | 10k | R0603F | R401, R402, R403, R404, R405 |
Warp esp32-ethernet v2-brick design files
The KiCad project lives in the Tinkerforge/warp-esp32-ethernet-v2-brick repository on GitHub; these links point at the commit this page was built from.
Warp esp32-ethernet v2-brick: common questions
What microcontroller does the Warp esp32-ethernet v2-brick use?
The Warp esp32-ethernet v2-brick is built around the ESP32-WROVER-E, from the ESP32 family.
How big is the Warp esp32-ethernet v2-brick PCB?
The Warp esp32-ethernet v2-brick measures 116.5 × 57.5 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Warp esp32-ethernet v2-brick?
211 components, from 81 distinct parts. The full bill of materials is listed on this page.
Where can I download the Warp esp32-ethernet v2-brick design files?
From the Tinkerforge/warp-esp32-ethernet-v2-brick repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Warp esp32-ethernet v2-brick design in my own project?
The repository has no license, so all rights stay with Tinkerforge. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Warp esp32-ethernet v2-brick without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k