RadioDev

tmolteno·TART-3·hardware/radio_dev_board/radioDev.kicad_pcb

RadioDev PCB layout, top view — open source AVR/Arduino board by tmolteno

About the RadioDev PCB

RadioDev is an open source AVR/Arduino PCB design by tmolteno, published on GitHub under the GPL-3.0 license. It is a 4-layer board measuring 100 × 75 mm, with 99 components from 42 distinct parts.

Its main chip is the ATmega328PB-AU, from the AVR/Arduino family. Other key parts include the SP3485CN, conn2x18pcie, FT232RL, DS90LV028 and 78M05_Switcher. By type, the board carries 32 capacitors, 28 resistors, 14 diodes, 11 ICs, 6 connectors and 4 switches.

It belongs with the rf & radio and science & space designs in this gallery.

From the project

The TART radio telescope, Version 3.

TART-3/hardware contains the physical design files.

TART-3/hardware/lna is the design for the seperate low noise front end required when using passive antennas.

Main components on the RadioDev

SP3485CNconn2x18pcieFT232RLATmega328PB-AUDS90LV02878M05_SwitcherLM1117-3.3

RadioDev bill of materials (BOM)

99 components, 42 distinct parts.

QtyPartRefs
1
SP3485CN
U1
1
conn2x18pcie
U2
2
FT232RL
U3, U11
1
ATmega328PB-AU
U4
4
DS90LV028
U5, U6, U7, U8
1
78M05_Switcher
U9
1
LM1117-3.3
U10
1
Q_NPN_CBE
Q1
1
DSB321SDA
X1
1
16MHz
Y1
1
Conn_02x03_Odd_Even
J1
2
Conn_01x05
J2, J3
2
USB_C_Receptacle_USB2.0V1
J4, J6
1
Barrel_Jack_MountingPin
J5
1
Reset
SW1
1
SW_Push
SW2
1
PGM
SW3
1
Misc
SW4
2
RX
D1, D13
2
TX
D2, D14
Show 22 more
QtyPartRefs
1
13
D3
1
A3
D4
1
A2
D5
1
A1
D6
1
A0
D7
3
D_Schottky
D8, D9, D10
1
5V
D11
1
3V3
D12
1
600Ohm
FB1
6
C
C1, C9, C10, C11, C12, C26
15
0.1
C2, C3, C4, C5, C6, C14, C16, C18 +7
2
27p
C7, C8
2
10u
C13, C19
1
4u7
C15
3
0.01
C17, C24, C27
2
10
C20, C23
1
1000p
C25
6
R
R1, R18, R19, R20, R21, R22
2
120
R2, R3
15
1K
R4, R5, R6, R7, R9, R10, R11, R12 +7
3
100K
R8, R27, R28
2
5.11K
R14, R15

RadioDev design files

The KiCad project lives in the tmolteno/TART-3 repository on GitHub; these links point at the commit this page was built from.

RadioDev: common questions

What microcontroller does the RadioDev use?

The RadioDev is built around the ATmega328PB-AU, from the AVR/Arduino family.

How big is the RadioDev PCB?

The RadioDev measures 100 × 75 mm, has 4 copper layers and is 1 mm thick.

How many components are on the RadioDev?

99 components, from 42 distinct parts. The full bill of materials is listed on this page.

Where can I download the RadioDev design files?

From the tmolteno/TART-3 repository on GitHub, which has the KiCad layout; the links under Design files point to each one.

Can I use the RadioDev design in my own project?

Yes, under the terms of its GPL-3.0 license, which tmolteno chose for the repository.

Can I test firmware for the RadioDev without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in TART-3

Similar boards