USD2PSX Base

tschicki·uSD2PSX·uSD2PSX_Base/uSD2PSX_Base.kicad_pcb

USD2PSX Base PCB layout, top view — open source RP2040/RP2350 board by tschicki

About the USD2PSX Base PCB

USD2PSX Base is an open source RP2040/RP2350 PCB design by tschicki, published on GitHub under the CERN-OHL-P-2.0 license. It is a 2-layer board measuring 24 × 32 mm, with 25 components from 12 distinct parts.

Its main chip is the RP2040, from the RP2040/RP2350 family. Other key parts include the APS6404L-3SQR-ZR and W25Q16JVUXIQ TR. By type, the board carries 12 capacitors, 8 resistors, 3 ICs, 1 crystal and 1 connector.

From the project

An SD-Card sized variant of SD2PSX

This variant of the SD2PSX is made specifically as an accessory for my PlayStation 2 portable. - Its electronics are based on and essentially 1:1 compatible to the original SD2PSX. - Form factor and pinout match an SD card, with one deviation: PS2 memory cards have an ACK signal that SD cards do not have - this is connected to pin 9, instead of DAT2. - While the uSD2PSX will fit in any SD card slot, only a PS2 will be able to access it. - The uSD2PSX may be used together with a regular PS2 console too, using a modified Bitfunx MX4SIO memory card.

USD2PSX Base, from the project README
From the project README

Main components on the USD2PSX Base

USD2PSX Base bill of materials (BOM)

25 components, 12 distinct parts.

QtyPartRefs
1
APS6404L-3SQR-ZR
LY68L6400SLIT
U4
1
W25Q16JVUXIQ TR
W25Q16JVUXIQ
U101
1
RP2040
U102
1
FL1200112
12MHz
Y101
1
MEM2085-00-115-00-A
MEM2085-00-115-00-A_REV0.2
J114
8
CC0402KRX7R7BB104
100n
C13, C101, C105, C106, C110, C111, C112, C113
2
CC0402JRNPO9BN150
15p
C102, C103
2
CC0603KRX7R7BB105
1u
C104, C114
2
RC0402JR-0710KL
10k
R9, R101
1
RC0402FR-071KL
1k
R104
2
RC0402FR-0722RL
22R
R105, R109
3
RC0402JR-07100RL
100R
R106, R107, R108

USD2PSX Base design files

The KiCad project lives in the tschicki/uSD2PSX repository on GitHub; these links point at the commit this page was built from.

USD2PSX Base: common questions

What microcontroller does the USD2PSX Base use?

The USD2PSX Base is built around the RP2040, from the RP2040/RP2350 family.

How big is the USD2PSX Base PCB?

The USD2PSX Base measures 24 × 32 mm, has 2 copper layers and is 0.6 mm thick.

How many components are on the USD2PSX Base?

25 components, from 12 distinct parts. The full bill of materials is listed on this page.

Where can I download the USD2PSX Base design files?

From the tschicki/uSD2PSX repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the USD2PSX Base design in my own project?

Yes, under the terms of its CERN-OHL-P-2.0 license, which tschicki chose for the repository.

Can I test firmware for the USD2PSX Base without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

More boards in uSD2PSX

Similar boards