Satnogs rotator controller
tt-laboratories·satnogs-rotator-controller·satnogs_controller/satnogs_controller.kicad_pcb
About the Satnogs rotator controller PCB
Satnogs rotator controller is an open source AVR/Arduino PCB design by tt-laboratories, published on GitHub under the CERN-OHL-1.2 license. It is a 2-layer board measuring 100 × 80 mm, with 65 components from 39 distinct parts.
Its main chip is the Arduino_Pro_Mini, from the AVR/Arduino family. Other key parts include the SN65HVD485EDR, Pololu_A4988, TPS54360DDA, Pololu_Dual_MC33926 and PCA9540B. By type, the board carries 19 resistors, 15 capacitors, 8 ICs, 8 jumpers, 7 connectors and 4 diodes.
From the project
Electronics designs for SatNOGS Rotator.
Electronics designs for SatNOGS Rotator.
Repository includes all source files of PCB's for the SatNOGS rotator controller assembly.
Firmware can be found on satnogs-rotator-firmware.
More information can be found in our wiki.
SatNOGS hardware repositories only track source design files. All needed derivative files (e.g. stl, grb etc) for production are created per release, packaged in an archive and uploaded linked to a release.
Main components on the Satnogs rotator controller
Satnogs rotator controller bill of materials (BOM)
65 components, 39 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Arduino_Pro_Mini | Arduino_Pro_Mini | U1 |
| 1 | SN65HVD485EDR | SOIC-8_3.9x4.9mm_Pitch1.27mm_HandSoldering | U2 |
| 2 | Pololu_A4988 | Pololu_A4988 | U3, U4 |
| 1 | TPS54360DDA | HSOP-8 | U5 |
| 1 | Pololu_Dual_MC33926 | Pololu_Dual_MC33926 | U6 |
| 1 | PCA9540B | TSSOP-8_3x3mm_Pitch0.65mm_HandSoldering | U7 |
| 1 | TC74 | SOT-23-5_HandSoldering | U8 |
| 1 | DEV-PINS | Pin_Header_Straight_2x04 | P1 |
| 1 | End-Stops | Pin_Header_Straight_2x03 | P2 |
| 1 | INPUT | Pin_Header_Straight_2x05_Pitch2.54mm | P3 |
| 1 | I2C | Pin_Header_Straight_2x04 | P4 |
| 1 | ISP | Pin_Header_Straight_2x03_Pitch2.54mm | P6 |
| 2 | Motor | MKDS_1.5-4 | P7, P8 |
| 1 | FUSE | Fuse_SMD1206_HandSoldering | F1 |
| 8 | Jumper_NO_Small | R_0805_HandSoldering | JP1, JP2, JP3, JP4, JP5, JP6, JP7, JP8 |
| 2 | D_Schottky | DO-214AB_Handsoldering | D1, D2 |
| 1 | D_TVS_x2_AAC | SOT-23_Handsoldering | D3 |
| 1 | D_TVS | DO-214AB_Handsoldering | D4 |
| 1 | FILTER - POWER | R_0805_HandSoldering | FB1 |
| 1 | FILTER | R_0805_HandSoldering | FB2 |
Show 19 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 27u | Inductor_Bourns-SRR1210_HandSoldering | L1 |
| 6 | 0.1u | C_0805_HandSoldering | C1, C10, C11, C12, C13, C14 |
| 1 | 2.2u | C_1210_HandSoldering | C2 |
| 3 | 100u | c_elec_6.3x5.3 | C3, C4, C5 |
| 1 | 100n | C_0805_HandSoldering | C6 |
| 1 | 7.5n | C_0805_HandSoldering | C7 |
| 1 | 10p | C_0805_HandSoldering | C8 |
| 1 | 47u | C_1210_HandSoldering | C9 |
| 1 | 100u | CP_Radial_D10.0mm_P5.00mm | C15 |
| 1 | 120 | R_0805_HandSoldering | R1 |
| 6 | 4.7k | R_0805_HandSoldering | R2, R3, R5, R6, R16, R17 |
| 2 | 100k | R_0805_HandSoldering | R4, R7 |
| 2 | 10 | R_0805_HandSoldering | R8, R9 |
| 1 | 221k | R_0805_HandSoldering | R10 |
| 1 | 26.7k | R_0805_HandSoldering | R11 |
| 1 | 147k | R_0805_HandSoldering | R12 |
| 1 | 10.5k | R_0805_HandSoldering | R13 |
| 2 | 200 | R_0805_HandSoldering | R14, R15 |
| 2 | 10k | R_0805_HandSoldering | R18, R19 |
Satnogs rotator controller design files
The KiCad project lives in the tt-laboratories/satnogs-rotator-controller repository on GitHub; these links point at the commit this page was built from.
Satnogs rotator controller: common questions
What microcontroller does the Satnogs rotator controller use?
The Satnogs rotator controller is built around the Arduino_Pro_Mini, from the AVR/Arduino family.
How big is the Satnogs rotator controller PCB?
The Satnogs rotator controller measures 100 × 80 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Satnogs rotator controller?
65 components, from 39 distinct parts. The full bill of materials is listed on this page.
Where can I download the Satnogs rotator controller design files?
From the tt-laboratories/satnogs-rotator-controller repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Satnogs rotator controller design in my own project?
Yes, under the terms of its CERN-OHL-1.2 license, which tt-laboratories chose for the repository.
Can I test firmware for the Satnogs rotator controller without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k